marantz PM7200 dead

sakis · 11th February 2010, 07:45 AM

so here it is a marantz PM7200 that is dead

The amplifier clicks from stand by that is audible then again after a few seconds protection clicks and all voltage appear to be normal inside

Front panel though is totally dead no led and absolutelly no control is working ....

in the first amplifier that i had to fix ( 2 of them come in to the shop with in 2 days ) i found that asmall TO92 device (S80820CL) located next to TMP87C846NG front procesor that is a voltage watch dog and provides reset to pin 18 was faulty

in the second amplifier was the exact same thing that caused the problem but also the processor was gone

in a third amplifier Yamaha that ihad to fix similar problems where caused by the same thing S80820CL

Alternative is that you may skip The S80820CL by connecting directly the pin18 of the prosessor to the diode and capacitor that is there thus providing voltage from Vdd to pin 18 for a constand reset ...

regards sakis

( there is no point on writing these but search engines will find it and may be some diyer will bennefit from it )

robahrc · 7th December 2010, 12:21 PM

Hi, Ive seen your reply on this site on one of the marantz problems:

I have a Marantz PM7200 which is in standby mode. (protection mode?) What it does:
-It powers on, measuring all circuits powered, but it does not respond to any remote control input.
-tested remote to be working 100% and sending out signals + equipped new batteries.
-When connected to speakers, it does not give any sound. Can you tell me what to do to get it working? Thanks in advance

11th February 2010, 07:45 AM	#1
sakis diyAudio Member Join Date: Jan 2006 Location: nea makri athens greece	marantz PM7200 dead so here it is a marantz PM7200 that is dead The amplifier clicks from stand by that is audible then again after a few seconds protection clicks and all voltage appear to be normal inside Front panel though is totally dead no led and absolutelly no control is working .... in the first amplifier that i had to fix ( 2 of them come in to the shop with in 2 days ) i found that asmall TO92 device (S80820CL) located next to TMP87C846NG front procesor that is a voltage watch dog and provides reset to pin 18 was faulty in the second amplifier was the exact same thing that caused the problem but also the processor was gone in a third amplifier Yamaha that ihad to fix similar problems where caused by the same thing S80820CL Alternative is that you may skip The S80820CL by connecting directly the pin18 of the prosessor to the diode and capacitor that is there thus providing voltage from Vdd to pin 18 for a constand reset ... regards sakis ( there is no point on writing these but search engines will find it and may be some diyer will bennefit from it ) __________________ SERVICE ΙΑΠΩΝΙΚΩΝ ΜΗΧΑΝΗΜΑΤΩΝ ΗΧΟΥ www.eastelectronics.gr

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Help Needed - Marantz 1060 dead channel	Wharf_Creek	Solid State	14	12th March 2010 04:23 PM
Help! Marantz CD63 dead!	wyman	Digital Source	2	23rd April 2009 07:27 PM
Marantz Pm7200 Amp	jjbmon	Solid State	3	22nd February 2009 08:46 PM
Marantz PM44SE - Dead(ish) right channel	nig123	Solid State	7	6th June 2007 06:29 AM
marantz pm7200 preamplifer	jules_gerfault	Solid State	0	16th February 2007 08:00 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

7th December 2010, 12:21 PM	#2
robahrc diyAudio Member Join Date: Dec 2010	Hi, Ive seen your reply on this site on one of the marantz problems: I have a Marantz PM7200 which is in standby mode. (protection mode?) What it does: -It powers on, measuring all circuits powered, but it does not respond to any remote control input. -tested remote to be working 100% and sending out signals + equipped new batteries. -When connected to speakers, it does not give any sound. Can you tell me what to do to get it working? Thanks in advance

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)