Robust Power Supply PCB suited to hi-quality amplifiers

RyanW · 28th March 2008, 07:07 AM

A PSU PCB Groupbuy is underway for a very robust power supply. It is suitable for typical split-rail amplifier supplies.

The PCB has provision for 8Ea x 35mm caps, Fuses, Rectifier diodes, CRC (or CLC or link out), etc...

Check the original forum for details:

http://www.diyaudio.com/forums/showt...80#post1468680

The tentative price for boards is $18.00 USD. More information can be found in the wiki:

http://www.diyaudio.com/wiki/index.p...ard+Group+Buy+

The Groupbuy is being managed by Landoctor. Please direct any questions to him within the original thread [Power Amp PSU Board (for e.g. LYNX Amp)]... see link above

This post is out of place (It should be under Groupbuys) but I have posted here to draw the attention of any Solid-state DIYers that will be building amps in the near future. The moderator can move this thread if necessary.

RyanW · 28th March 2008, 07:10 AM

Silk

RyanW · 28th March 2008, 07:12 AM

Top

RyanW · 28th March 2008, 07:13 AM

bottom

peranders · 28th March 2008, 07:58 AM

A good advice from me: Make first a small prototype run in order to debug the pcb.

Jan Dupont · 28th March 2008, 01:06 PM

I have promised landoctor that I will make a cosmetic update (primary the silk screen) this weekend.

I will post it here when done

RyanW · 28th March 2008, 02:59 PM

ACD,

Sounds good. Thanks again for the design work and for spearheading the Groupbuy.

Peranders,

Agreed. I'd hate to manufacture 200 PCB's and find that there is a mistake. The board is pretty straightforward but Murphy's law has a way of sneaking up on you.

Cheers,

Ryan

MadFinn · 28th March 2008, 03:00 PM

Hopefully there will be a groupbuy on these PCB also
Got my Lynx PCB's today REALY NICE

Thanx Jan

RyanW · 28th March 2008, 03:01 PM

Perhaps someone who has the facilities in place to DIY a home-made board could do a test board.

Ragnwald · 28th March 2008, 03:51 PM

Hi

Is it possible to show a simpel schematic of the boards facilities and usefulness?

regards

28th March 2008, 07:07 AM	#1
RyanW diyAudio Member Join Date: Apr 2005 Location: Vancouver, BC	Robust Power Supply PCB suited to hi-quality amplifiers A PSU PCB Groupbuy is underway for a very robust power supply. It is suitable for typical split-rail amplifier supplies. The PCB has provision for 8Ea x 35mm caps, Fuses, Rectifier diodes, CRC (or CLC or link out), etc... Check the original forum for details: http://www.diyaudio.com/forums/showt...80#post1468680 The tentative price for boards is $18.00 USD. More information can be found in the wiki: http://www.diyaudio.com/wiki/index.p...ard+Group+Buy+ The Groupbuy is being managed by Landoctor. Please direct any questions to him within the original thread [Power Amp PSU Board (for e.g. LYNX Amp)]... see link above This post is out of place (It should be under Groupbuys) but I have posted here to draw the attention of any Solid-state DIYers that will be building amps in the near future. The moderator can move this thread if necessary.

28th March 2008, 07:58 AM	#5
peranders Electrons are yellow and more is better! diyAudio Member Join Date: Apr 2002 Location: Göteborg, Sweden Blog Entries: 4	A good advice from me: Make first a small prototype run in order to debug the pcb. __________________ /Per-Anders (my first name) or P-A as my friends call me Tube Buffered Gainclone in work \|Thread

28th March 2008, 01:06 PM	#6
Jan Dupont diyAudio Member Join Date: Apr 2003 Location: Copenhagen, Denmark	I have promised landoctor that I will make a cosmetic update (primary the silk screen) this weekend. I will post it here when done __________________ Free Schematic and Service Manual downloads www.audio-circuit.dk, Company: www.dupont-audio.com, Joint venture: www.DupontMantra.com

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Can i use a computer power supply to power audio amplifiers?	destroyer X	Solid State	91	25th September 2006 04:36 AM
UcD HG power supply sound quality?	ghemink	Class D	6	4th August 2005 04:01 PM
quality of power supply	trancy	Tubes / Valves	3	23rd March 2004 01:02 PM
Power supply oil capacitors for your SE triode amplifiers	CCOZGO40	Swap Meet	0	12th August 2002 03:01 PM


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

28th March 2008, 02:59 PM	#7
RyanW diyAudio Member Join Date: Apr 2005 Location: Vancouver, BC	ACD, Sounds good. Thanks again for the design work and for spearheading the Groupbuy. Peranders, Agreed. I'd hate to manufacture 200 PCB's and find that there is a mistake. The board is pretty straightforward but Murphy's law has a way of sneaking up on you. Cheers, Ryan

28th March 2008, 03:00 PM	#8
MadFinn diyAudio Member Join Date: Jan 2006 Location: Småland	Hopefully there will be a groupbuy on these PCB also Got my Lynx PCB's today REALY NICE Thanx Jan

28th March 2008, 03:01 PM	#9
RyanW diyAudio Member Join Date: Apr 2005 Location: Vancouver, BC	Perhaps someone who has the facilities in place to DIY a home-made board could do a test board.

28th March 2008, 03:51 PM	#10
Ragnwald diyAudio Member Join Date: Feb 2008 Location: Gotland	Hi Is it possible to show a simpel schematic of the boards facilities and usefulness? regards

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read