diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Solid State (http://www.diyaudio.com/forums/solid-state/)
-   -   OMG what have I done? (http://www.diyaudio.com/forums/solid-state/113376-omg-what-have-i-done.html)

Pbassred 10th December 2007 12:11 PM

OMG what have I done?
 
a 2 channel MosFET power amp using 2 pairs of K135/J50. On a parent board plus a further 3 pairs on a daughter board.

The actual work wasn't that much. The MOSFETs are on TO3 packages and the brass bushes that they are bolted to had cracked their soldered joints. Unbolt to break the heat path to the devices, remove old solder, clean up flux, resolder, clean boards. While its apart, replace the electrolytics and check orientation. All quite within my capabilities.

Result:- no output. All the devices make more heat 45deg C as opposed to 30deg C in the untouched chanel. The power rails are steady at 75V.
So my questions are:

What would make it run hard but give no output? There is no DC at the output either. At switch off, the resistance across the speaker terminals is identical on both chanels.

Can I disconnect the top board since its only a parallel board?

I don't have access to a scope :(

schematic

phase_accurate 10th December 2007 01:26 PM

I have one of these as well (can be seen here: http://www.diyaudio.com/forums/showt...03#post1266503).
A long time ago there were problems arising with the output relays. Maybe this is the case with yours as well.

Where did you measure for DC "at the output" ? On the backplane or on the PCB ? If there is no DC on the output sochet/clamps doesn't mean that there is no DC at the amp outout as such since there is the DC protection inbetween so watch out !

BTW: If the bias current is set to the recommended value this amp doesn't get warm - it gets HOT !

Regards

Charles

Pbassred 10th December 2007 03:48 PM

http://i76.photobucket.com/albums/j2...0topresize.jpg
This is mine. Never noticed it get hot but them I never hd cause to turn it up. Its older than the drawings that I have. I can hear the output relays working and I didn't have any problem before. So its logical to assume that it is something I did.

I have been building electronic equipment for the last 15 years but as to how it works - my knowledge is ....simplistic.

You say that know the "recomended value" of the bias. Do you have some other schematics?

First thing first though; If the top PCB is just more fets in parrallel, can I operate the amp with it completely removed? It would give me space to move.

Zero Cool 10th December 2007 04:46 PM

Check to make sure the output relays aren't shorted. a common problem with Ampeg Bass amps is that the relays short out when they go bad. they switched the speaker load from ground to the output of the amp. when the relays go bad they still click, but the output of the amp is shorted to ground.

Also, the K135/J50 mosfets like to blow the gates if the amp is overdriven and there isn't sufficient gate overdrive protection. the output can and will oscillate like crazy.

<shrug> just ideas

Pbassred 10th December 2007 05:07 PM

If the output relay was shorted it would get VERY hot. Possibly pull down the supply voltage. No?

If a single device went bad it would either go very hot or very cold, but these are evenly warm.

phase_accurate 11th December 2007 10:47 AM

My relays click also but they have bad contacts (like the mains switch that you'll have to replace on these amps every few years).

BTW: I have a copy of the whole service manual.

And I must say if it weren't for the age-related ailments this would still be a very fine amp. I used it for the hornloaded small-P.A. from the above link, as bass-amp (in conjunction with a DIY bass-preamp) and for listening at home (bass section of Klipschorn copy - actively driven :devilr: ).

Regards

Charles

Pbassred 11th December 2007 12:45 PM

Do you have the manual in electronic form? Or could it be scanned?

phase_accurate 11th December 2007 01:38 PM

1. No
2. Yes !

Regards

Charles

Pbassred 11th December 2007 09:09 PM

Quote:

BTW: I have a copy of the whole service manual.
well.......er
er
er would you mind?

Please?

Checked the relay contacts. They seem ok

phase_accurate 12th December 2007 06:53 AM

Sorry, I forgot to undig the **** manual last night. Will do it tonoight.

Regards

Charles


All times are GMT. The time now is 10:40 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2