Quiescent Current - diyAudio
Go Back   Home > Forums > Amplifiers > Solid State

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 11th November 2001, 02:18 PM   #1
diyAudio Member
 
Join Date: Nov 2001
Location: UK
Hello Out There

I have built myself a Power Amplifier using Hitachi mosfets, 2SK176 and 2SJ56, two per channel which run from supply rails up to +/- 100V and will deliver a maximum output of 68V rms. The quiescent current was set at 155mA and this is the question I would like answered. I have recently seen on the net people suggesting that the bias current can be increased to give better sound quality. If this is a viable action could anyone tell me to what level I could increase the quiescent current on my amp. I also have a recent problem of the imaging drifting to the left. I have eliminated everything from the equation and it is the power amp that is at fault. I was wondering if the standing current could be the possible cause, that it might have drifted, as you can see I am a novice when it comes down to electronics. I would appreciate any help, veiws or answers to the above.

Cheers!!
  Reply With Quote
Old 11th November 2001, 10:20 PM   #2
diyAudio Member
 
Join Date: Feb 2001
Location: Columbia, SC
John,
The more current you use, the closer to class A you will get. This will entail more heat. You'll need to consult the SOA charts for your devices and keep in mind that your heatsinks will get pretty toasty if you start jacking up the bias. The power supply will need to be able to supply the necessary current without coming unstuck.
That said, class A operation is one ingredient of good sound.

Grey
  Reply With Quote
Old 11th November 2001, 10:49 PM   #3
diyAudio Member
 
Join Date: Nov 2001
Location: UK
Thanks Grey

I am using heatsinks fom an industrial robot no less and at the recommended bias setting of 155mA they barely get warm so as far as that is concerned I should be OK. The power supply is based around a 1Kva transformer and 88000 mfd of capacitors which have been bypassed with high quality polypropylenes so there should be no problem there.
Where and what are the SOA charts that you refer to and what information will they relate to. If all looks good I might try increasing the quiescent current in 25mA steps and monitor what happens and also see if the overall performance improves. What do you think???

John
  Reply With Quote
Old 11th November 2001, 11:03 PM   #4
diyAudio Member
 
Join Date: Jan 2001
Location: Scandinavia
You can find SOA curves on device data sheets. SOA means safe operation area. This is limited by power (y=1/X shape curve), max operating voltage, max operating current etc. Then there is the substrate thermal, usually max 150-175degC but you need to stay well below that.

It is unlikely that your drift is a class A issue, more likely a drift situation, perhaps in the driver stage given your usage of industrial components

Petter
  Reply With Quote
Old 11th November 2001, 11:40 PM   #5
diyAudio Member
 
Join Date: Nov 2001
Location: UK
Thank you Petter

I have had a look at the available information that I have to hand and this tells me that these particular mosfets have the following specification: (a) Id max/A = 8.00 (b) RDS max/ohms = 1.5 (c) Pd max/W = 125 (d) Vds max/V = 200
As I stated previously I am no electronics buff so I find it difficult to keep up with you guys. Based on the specs could you tell me if the quiescent current could be increased without a major catastophy. Can anyone explain when and how an amp is said to be class A and is this a simple matter of increasing the bias to a certain point or is there more to it than this.

Cheers John
  Reply With Quote
Old 12th November 2001, 12:33 AM   #6
diyAudio Member
 
Join Date: Feb 2001
Location: Columbia, SC
John,
The specs you mention are, unfortunately, in isolation--meaning that you can have the 8A, but not at the same time as the 200V (note that 8A * 200V would yield 1600W--well beyond the 125W case limit). The SOA chart (aka SOAR on some datasheets, the R at the end standing for Region) should be somewhere in the data sheets. I don't keep Hitachi data sheets around, as I can't get the parts reliably.
Does their website not provide complete information on their devices?

Grey
  Reply With Quote
Old 12th November 2001, 01:35 AM   #7
grataku is offline grataku  United States
diyAudio Member
 
Join Date: Dec 2000
Location: -
John,
first of all, from what I understand not all class AB amps really benefit from jacking up the bias current in search of the audio holy grail known as class A. There are other types of distortion besides xover that may actually increase the total distortion of the amp if the amplifer is not designed to operate in class A to begin with.
I don't know what kind of design you are using but from simple transistor considerations a 125 w device operating at 100V will be very ill-disposed to tolerate much more than 0.5 amps. For that matter, I think that one pair of these mosfet would be undersized in an amp operating at 1/2 of the voltage you are using right now!
  Reply With Quote
Old 12th November 2001, 07:33 AM   #8
djk is offline djk
diyAudio Member
 
djk's Avatar
 
Join Date: Feb 2001
Location: USA
The suggested bias for Hitachi lateral MOSFETs is 100mA per device.If you are running two pair per channel that would be 200mA plus the current from your driver circuit, say another 50mA, for a total of 250mA per channel.With +/- 100V and only two pair of outputs only 8 ohms may be driven.As far as the image drifting the first thing I would look at would be the cap in the feedback loop to ground.Usually an elecrolytic due to the size, this part is critical.If the image drifts to the left, the cap in the right channel is usually at fault.Replace with as high a quality non-polar as you can afford, and bypass with a small film type.To prevent damage to this cap a pair of reverse paralleled glass diodes should be used (1N4148 or similar).
  Reply With Quote
Old 12th November 2001, 06:20 PM   #9
diyAudio Member
 
Join Date: Nov 2001
Location: UK
Default Thank you all

I am really pleased at the response I've had from all you guys I didn't expect all the help that I have received. I shall try and digest everything that you have imparted and will let you know at a later date what, if anything, I have done and what the overall benefits were.
Thanks to everyone

John
  Reply With Quote
Old 12th November 2001, 07:12 PM   #10
The one and only
 
Nelson Pass's Avatar
 
Join Date: Mar 2001
While Bipolar AB amps often do not benefit all that
much from higher bias current, the Mosfets definitely
do, and I would suggest that most of the complaints
about Mosfets stem from low bias performance.

I would suggest that you crank the bias up until you
are running 25-30 watts each, which is about 250-300 mA
per device, assuming that you can still touch them after
a half hour or so.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Quiescent Current Luxman M-03 Weide Solid State 5 7th January 2012 10:33 AM
Quiescent current question? thanks crippledchicken Solid State 29 18th June 2005 09:58 PM
LM3886 Quiescent current NITRO Chip Amps 4 20th April 2005 10:06 PM
P3a No quiescent current! PetarLD Solid State 9 17th February 2004 01:20 AM
LM3886 and it's quiescent current Toster Chip Amps 5 5th May 2003 10:23 PM


New To Site? Need Help?

All times are GMT. The time now is 02:06 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2