Peavey 2000 Drawing huge amounts of current. - diyAudio
Go Back   Home > Forums > Amplifiers > Solid State

Solid State Talk all about solid state amplification.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 19th October 2007, 01:07 AM   #1
diyAudio Member
 
Join Date: Oct 2007
Default Peavey 2000 Drawing huge amounts of current.

I got a peavey 2000 a few days ago and it came in with the complaint of it smoking. so i got it, replaced the sacrificial triac. and a speachel qaulity ic i looked for any obvious troubles like shorted drivers, outputs, and diodes and the like. all seamed to be fine. i tunred it on slowly with just channel b in it with a variac it draws 5 amps at 100 volts with or with out a single through it. when i put a wave through it it put out a good sine wave. but ive fixed a few of these and never noticed it draw so much current. Then i was like well ok ill try channel a. so i did the same to it And it draws Huge amounts of current at about 20-35 volts it pulls 6-10 amps, but it puts out a nice sine wave . i know if i were to plug it in it would def blow. im really lost in this and have called peaveys tech support several times. they seamed to be stumped to. so please if any one on here knows any solution or has come across this problem before then give me some pointers or lead me to the right place to get some answers. Thanks
  Reply With Quote
Old 19th October 2007, 11:14 AM   #2
djk is offline djk
diyAudio Member
 
djk's Avatar
 
Join Date: Feb 2001
Location: USA
If you could try again in English it would help.
__________________
Candidates for the Darwin Award should not read this author.
  Reply With Quote
Old 19th October 2007, 11:51 AM   #3
tade is offline tade  United States
diyAudio Member
 
Join Date: Feb 2005
Location: Ralieigh nc
Send a message via AIM to tade
As far as I can tell, that was English. I don't know what language you are fluent in...

I would suggest trying to isolate the amp circuitry from the PSU and see if the fault lies at either place. It might be a blown voltage regulator though I couldn't see sinking five amps there. perhaps it is a short inside the transformer? Does the transformer hum or get hotter than usual?

You said that you made some changes to the amp; could you be more specific about those? Also, the previous customer complained of smoke? That means that there is heat. If you can try and replicate the fault condition safely... Unplug the amp and see where you could fry an egg. All those amps have to go somewhere!

Good luck
  Reply With Quote
Old 19th October 2007, 03:53 PM   #4
diyAudio Member
 
Join Date: Jul 2005
Location: North Derbyshire
As suggested, the current must be going somewhere, and there are only a small number of places high currents can go.

But an amplifier of this type isn't something for tinkering with, you have to know what you're doing.
__________________
Nigel Goodwin
  Reply With Quote
Old 19th October 2007, 07:57 PM   #5
diyAudio Member
 
unclejed613's Avatar
 
Join Date: Dec 2006
IIRC Peavey uses fixed bias in this amp, so check for an open diode in the bias string. you will get a nice sine wave, but the output stage running way too much current. Peavey's fixed bias usually sets the outputs right at cutoff (which results in some xover notch, but these amps are rarely run at low power). they should be drawing 10mA or less at idle.
__________________
Vintage Audio and Pro-Audio repair ampz(removethis)@sohonet.net
spammer trap: spammers must die
  Reply With Quote
Old 20th October 2007, 01:22 AM   #6
djk is offline djk
diyAudio Member
 
djk's Avatar
 
Join Date: Feb 2001
Location: USA
He may have a shorted pre-driver in the output stage as well.

I dislike the habit of American young adults that deliberately use poor spelling, punctuation, grammar, syntax, etc.

As they said in times gone by:

"Get a haircut and get a real job"
__________________
Candidates for the Darwin Award should not read this author.
  Reply With Quote
Old 20th October 2007, 05:00 PM   #7
diyAudio Member
 
east electronics's Avatar
 
Join Date: Jan 2006
Location: Athens GREECE
Default unlike my

other friends and since happend to me before the first thing you do is to check the rectifier it could just as well be half blown and or leacky resulting drawing of so much current

to pevay amps happend to me twice so far

then i would disconenct both chanels power leads to make first sure that psu and trafo working properly .....(remember to discharge caps before reconnecting leads to boards !!!!!!!!)

use a lamp as a load and it has to be some ammount of watts cause in this way also you may evaluate how good is your elctrolytics ...... way to much voltage drop with or without load is hinch of capacitor problem ......


last there is a remote chance that you have a leacky trafo very litle chance to happen on pevay machine but possible especially if the amp has been running on some big pa possibly powered by genarators

regards sakis
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Karlson - "equal amounts of energy"- what did he mean? freddi Multi-Way 8 25th May 2007 06:44 PM
My first GC PCB drawing... flying Chip Amps 8 14th January 2005 06:24 AM
CAD Drawing Doug Everything Else 8 8th October 2003 02:52 PM
Switching Large amounts of FETs fr0st Parts 20 30th August 2003 10:19 AM
NonInverting Gain Amounts MantramAudio Chip Amps 3 11th August 2003 05:55 PM


New To Site? Need Help?

All times are GMT. The time now is 07:28 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2