How to calculate a subsonic filter for phono pre?
 User Name Stay logged in? Password
 Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read Search

 Solid State Talk all about solid state amplification.

 Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
 15th May 2007, 05:18 PM #1 Kal   diyAudio Member   Join Date: Aug 2003 Location: Germany How to calculate a subsonic filter for phono pre? Hello, can someone please help me calculating a first order subsonic filter? I have a separate phono pre amp connected to my pre amp. The input impedance of my pre amp is 75 mV and 47 KOhm and I want to put the filter between my phono pre and the pre. I think about a soft first order filter around 20 to 30 Hz. What do I need and how do I have to connect it? Thank you!
 16th May 2007, 10:52 AM #2 AndrewT   diyAudio Member   Join Date: Jul 2004 Location: Scottish Borders Hi, your RIAA may already have the subsonic filter built into it's circuit. The original RIAA was supposed to be flat below 20Hz but they brought out a new curve specification about 20years ago with a highpass roll off from about 30to 40Hz. In my opinion, this killed the bass from records and as a result ruined the performance. I reverted to the older specification. __________________ regards Andrew T.
 16th May 2007, 11:02 AM #3 richie00boy   Did it Himself diyAudio Member     Join Date: Nov 2003 Location: Gloucestershire, England, UK If your input impedance is 47k then the good old formula C = 1 / (2 . pi . F . R) is what you need C is in Farads (divide by 1000000 to get microfarads) F is in Hertz R is in ohms (multiply kilohms by 1000 to get ohms) __________________ www.readresearch.co.uk my website for UK diy audio people - designs, PCBs, modules and more.
 16th May 2007, 01:08 PM #4 RogerGustavsson   diyAudio Member   Join Date: Aug 2004 Location: Huskvarna A subsonic filter with only a first order cut will not be very useful. If you put a 0.15 µF capacitor in series with the signal, you will get a cut off below 22 Hz (0.1 µF and the cut off starts at 33 Hz). A third order filter (18 dB/octave) at 25 Hz is better suited. Why do you need a subsonic filter? Roger
 17th May 2007, 10:31 AM #5 Kal   diyAudio Member   Join Date: Aug 2003 Location: Germany Thank all of you so far! I know that a subsonic filter will harm the sound in some way therefore I only want to use a soft first order filter, since subsonics look so scary with my 17cm mid/bass making big jumps...
 17th May 2007, 03:25 PM #6 ashok diyAudio Member     Join Date: Jun 2002 Location: 3RS Looks like your cartridge/tone arm is not damped well at subsonic frequencies. Typically the resonance should be around 10 Hz (?) and should be well damped. You can add a fluid damping device to your arm and reduce the resonance peak and its frequency. You will need a small container to hold the oil ( silicone oil or something similar ) and a paddle that is fixed to your tone arm. It also cleans up the bass very nicely. Some experimentation is required. I used to have a whole set of Japanese articles on fluid damping. Can't find even one sheet __________________ AM
RogerGustavsson
diyAudio Member

Join Date: Aug 2004
Location: Huskvarna
Quote:
 Originally posted by Kal Thank all of you so far! I know that a subsonic filter will harm the sound in some way therefore I only want to use a soft first order filter, since subsonics look so scary with my 17cm mid/bass making big jumps...
A first order filter is of very little use in your situation. If your bass drivers are pulsating, you probably have a “bad” combination of arm and cartridge. The frequency of resonance is too low and warped discs will not play back very well.

There are several ways of how to reduce this. One of them is mentioned by ashok, fluid damping of the arm. You can also connect the signal in mono below circa 50 Hz (it is already in mono on the disc anyway but means you need to modify your amplifier) or use a third or fourth order filter to cut the lowest frequencies. Such a filter will not harm the sound very much. It will certainly unburden your speakers and let them perform better.

My own RIAA amplifier, have these options included.

You can have a schematic if you like. Just let me know your E-Mail address.

Roger

 17th May 2007, 10:47 PM #8 audiobomber   diyAudio Member     Join Date: Jul 2004 Location: Sudbury, Ontario Canada Although it would seem that a first-order filter won't be much use, in fact it does the job pretty well. My old Bryston .5B had a first-order infrasonic filter, -1 dB @ 31Hz according to the spec sheet. At the time I was using a Grado Signature which had very little internal damping, a tonearm with no damping, and ported speakers. The woofers were flapping quite a lot, and the filter cut it out completely, so I suggest you go for it. __________________ Dan
audiobomber
diyAudio Member

Join Date: Jul 2004
Quote:
 Originally posted by richie00boy If your input impedance is 47k then the good old formula C = 1 / (2 . pi . F . R) is what you need C is in Farads (divide by 1000000 to get microfarads) F is in Hertz R is in ohms (multiply kilohms by 1000 to get ohms)
I've always wondered about the F in this formula. Is F the frequency at which the filter starts to act, or the -3 dB point, or what? I've always assumed it was -3dB, but never seen it confirmed.
__________________
Dan

 18th May 2007, 03:00 AM #10 ashok diyAudio Member     Join Date: Jun 2002 Location: 3RS Yes it is the -3dB point. __________________ AM

 Posting Rules You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules
 Forum Jump User Control Panel Private Messages Subscriptions Who's Online Search Forums Forums Home Site     Site Announcements     Forum Problems Amplifiers     Solid State     Pass Labs     Tubes / Valves     Chip Amps     Class D     Power Supplies     Headphone Systems Source & Line     Analogue Source     Analog Line Level     Digital Source     Digital Line Level     PC Based Loudspeakers     Multi-Way     Full Range     Subwoofers     Planars & Exotics Live Sound     PA Systems     Instruments and Amps Design & Build     Parts     Equipment & Tools     Construction Tips     Software Tools General Interest     Car Audio     diyAudio.com Articles     Music     Everything Else Member Areas     Introductions     The Lounge     Clubs & Events     In Memoriam The Moving Image Commercial Sector     Swap Meet     Group Buys     The diyAudio Store     Vendor Forums         Vendor's Bazaar         Sonic Craft         Apex Jr         Audio Sector         Acoustic Fun         Chipamp         DIY HiFi Supply         Elekit         Elektor         Mains Cables R Us         Parts Connexion         Planet 10 hifi         Quanghao Audio Design         Siliconray Online Electronics Store         Tubelab     Manufacturers         AKSA         Audio Poutine         Musicaltech         Aussie Amplifiers         CSS         exaDevices         Feastrex         GedLee         Head 'n' HiFi - Walter         Heatsink USA         miniDSP         SITO Audio         Twin Audio         Twisted Pear         Wild Burro Audio

 Similar Threads Thread Thread Starter Forum Replies Last Post djronbxs Solid State 0 27th November 2007 07:43 AM jakelm3075 Subwoofers 14 16th March 2006 02:55 PM Geez Subwoofers 7 9th August 2005 06:50 AM BobM Analogue Source 4 25th August 2003 06:21 PM guylemar Subwoofers 10 28th March 2003 02:38 AM

 New To Site? Need Help?

All times are GMT. The time now is 02:14 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.