Help me find a Mosfet/Transistor amp project useing what I have available??

[Minion]

Hi Folks, I asked a simular question a couple weeks ago but I was looking for a Low power Transistor amp and with the help of some of the members here and was able to Build a aprox 20w transistor amp useing a Tip41/42 and a BC550/560 and an OPA627 and had an all Fet Preamp stage and the pelimary tests on this simple design are encourageing.......

But now I have gotten some more transistors and some Mosfets which I would like to use to build a Higher powered amp but I can"t find a design that uses the parts I have available so that Is why I am here asking you guys ......

So here are some of the Parts I have available:

Power

IRF630 N-Ch Mosfet (200v 9A ) 10 Pieces
RFP8P08 P-Ch Mosfet (80v 8A) 10 Pieces
MJE3055 NPN (60v 10A) 10 Pieces
MJE2955 PNP (-60 10A) 10 Pieces
Tip125 Darlington PNP (-60v 5A) 5 Pieces
Tip 41C/42C NPN/PNP (100v 10A) 1 each
Tip30C/31C NPN/PNP 1 each

Small signal

2N4401/2n4403 Lots
2n3904/2n3906 Lots
BC550/BC560 a few
2N2222 Lots

Opamps (IC"s)
NE5532
OPA134
TL072
OPA602
OPA627
OPA2277
LM3886
LA6324
JRC 5719
JRC 5005
INA103
INA217

XFormers (Power)
2 x 28v 200vA
2 x 18v 100vA


For me it is OK if there are Opamps in the design as it worked out for my Last Transistor amp and it doesn"t need to be High fi and I don"t mind Paralelling several devices.......

If anyone has any suggestions I would love to hear them.......

Thanx a Lot Guys & Gals......


Cheers

 

[Leolabs]

Sounds like only mid power stuff can be build based on what you have.

 

[Minion]

Well I"m not looking for a 500w amp or anything Maybe 50w to 100w Max....

I was hopeing to use the 2x28v 200vA Transformer for the PSU (2x40v DC) which I"m sure could only power a 50w or maybe 75w Transistor/Mosfet amp.......

Anything in this Power range would be Good , I would be useing it as the Power stage for a Guitar or bass amp and I would have a seperate High Gain Preamp which will have at least 5v-7v of output......

Can someone point me in the Right Direction.??......


Thanx


PS: the Amp I just built produces 30w into 4 ohms or 18w into 8 ohms useing a Single Tip41/42(10A at 100V) and a single BC550C/560C and an Opa627 and a 50vA PSU so I"m sure it should be Possible to Paralell a few IRFP630 9A 200v devices to get close to 75w useing a 200vA transformer or Paralell several Tip3055/2955(10A 60v) to get simular power???

 

[redrabbit]

How about these ?
I have not built either one.
I am not qualified to know if used as guitar amp though..??
-----------------
ESP's Death of Zen
http://sound.westhost.com/project36.htm

----------------------
JLH Main Page....
http://www.tcaas.btinternet.co.uk/index-1.htm

The JLH classA...
http://www.tcaas.btinternet.co.uk/jlh1996.pdf

Part substitutes....
http://www.tcaas.btinternet.co.uk/jlhtrans.htm

=RR=

 

[Minion]

Thanx But none of them are Suitable.......

Anyone have any other Ideas??

 

[sixtek]

What about the ST151?
With 2×28V/200VA transformer in the PSU and using MJE2955/MJE3055s (3 pair pair module - 'cause of SOA). Of course you'll need to check Vceo0 of MJE's. At least 80V needed.

 

[sixtek]

The schematic

 

[sixtek]

The PCB

 

[sixtek]

The parts placing

 

[gmphadte]

ETI 480, 50W into 8 ohms

 

[Minion]

Thanx for the Schematic and Project Idea......

What do you suggest for a substitution Part for the BD139/140 and the BC547 and BC557 ?? the Subs have to be out of the Parts I listed in my original Post......

Thanx

 

[gmphadte]

Compare Vce and Ic(max) for the transistors in the design with available transistors. If yours have higher value than the specified, then it is ok to use them.

Be careful of the pinouts. They will definately be not the same.

Enjoy
Gajanan phadte