
Home  Forums  Rules  Articles  diyAudio Store  Gallery  Wiki  Blogs  Register  Donations  FAQ  Calendar  Search  Today's Posts  Mark Forums Read  Search 
Software Tools SPICE, PCB CAD, speaker design and measurement software, calculators 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools  Search this Thread 
3rd December 2014, 06:47 PM  #1 
diyAudio Member
Join Date: Dec 2014

PSpice simulation

5th December 2014, 03:06 PM  #2 
diyAudio Member
Join Date: Jul 2011
Location: Austria

Use two coils L1 and L2 and couple them with the statement "K12 L1 L2 0.99".

8th December 2014, 02:59 AM  #3 
diyAudio Member
Join Date: Oct 2004
Location: Adelaide South Oz

Universal Transformer Model.
This has Ultralinear Taps but just connect them to 0V via say 10Meg resistors for simulating the Bassman otherwise the simulator will have a "dummy spit". (Dummy is Oz vernacular for a babies pacifier). ************************************** * * Center Tap Audio Transformer, * for pushpull tube operation, * with screen grid taps * * TransPPSGT * * Primary Terminals * P1, P2 plate connections * Sg1, Sg2 screen grid connections * B primary center tap (+Vpp) * Secondary terminals * Sp1, Sp2 speaker connections * * * Parameters : * RP one half primary winding resistance * LA one half primary winding inductance * LP one half primary inductance, plate to screen tap * LS one half primary inductance, screen tap to center tap * RA impedance ratio, primary plateplate to secondary * RS secondary winding resistance * * the parameters are related to frequency response as follows : * let Rs = source resistance ( ie the load at the seen by the plate ) * let RL = load resistance ( ie the speaker ) * then RA = Rs/RL =n^2, where n is turns ratio, Ts/Tp * let r1 = total primary winding resistance * let r2 = total secondary winding resistance * let F1 = upper 3dB frequency * let F2 = lower 3dB frequency * if 3dB points are not known, but 1 dB points are, then * let F1' = upper 1dB frequency, * let F2' = lower 1dB frequency * then F1 = F1' x 2 * F2 = F2' / 2 * * then calculate total series inductance La * La = (Rs + r1 + (n^2)( RL + r2))/( 2 x pi x F1 ) * * then calculate total parallel inductance Lb * Lb = (Rs +r1)(RL + r2) (n^2)/((Rs + r1 +(n^2)(RL +r2))x 2 x pi x F2) * * then divide up La and Lb into the multiple windings required * let t be the screen grid tap percentage, * ie for a 40% screen grid tap, t = 0.40 * then the parameters are * RP = r1 / 2 * RS = r2 (NOTE : RS is NOT Rs !!) * LP = (1t)Lb/2 * LS = t x Lb/2 * LA = La/2 * * the default parameter values given are for an 8K to 8ohm transformer, * with 40% screen grid taps, * and 30 to 30KHz frequency response (15 to 60KHz 3dB response) * .SUBCKT TransPPSGT P1 Sg1 B Sg2 P2 Sp1 Sp2 * PARAMS: RP=25 LA=0.02234801 LP=13.3822388 LS=8.921493 RA=1000 RS=0.8 * * primary * RP1 P1 1 {RP} La1 1 2 {LA} LP1 2 3 {LP} LS1 4 5 {LS} LS2 6 7 {LS} LP2 8 9 {LP} La2 9 10 {LA} RP2 10 P2 {RP} RP3 3 Sg1 1 RP4 Sg1 4 1 RP5 5 B 1 RP6 B 6 1 RP7 7 Sg2 1 RP8 Sg2 8 1 * * secondary * Rs Sp1 11 {RS} LSA 11 Sp2 {8*(LP +LS)/RA} * * coupling * Kcore1 LP1 LS1 .999999 Kcore2 LP1 LS2 .999999 Kcore3 LP1 LP2 .999999 Kcore4 LP1 LSA .999999 Kcore5 LS1 LS2 .999999 Kcore6 LS1 LP2 .999999 Kcore7 LS1 LSA .999999 Kcore8 LS2 LP2 .999999 Kcore9 LS2 LSA .999999 Kcore10 LP2 LSA .99999 .ENDS TransPPSGT You should be able to modify this easily to suit the Bassman (or anything else). Also have a look in the Vaccuum Tube Spice models sticky at the top to see if anyone has put output tranny models in there. Cheers, Ian Last edited by gingertube; 8th December 2014 at 03:03 AM. 
8th December 2014, 08:03 AM  #4 
diyAudio Member
Join Date: Oct 2008

For a quick fix you could use an L//R.
Gingertube.. Do you know if this would fit into circuitmaker? Oh, and is Huey active on your side of the stump? There's no let up here, may try to hit up my car insurance for a spray job. 
8th December 2014, 10:16 AM  #5 
diyAudio Member
Join Date: Mar 2012
Location: Den Helder The Netherlands

You can try this one if you have EXCEL running on your pc you can configure it yourself

8th December 2014, 10:00 PM  #6  
diyAudio Member
Join Date: Oct 2004
Location: Adelaide South Oz

Quote:
http://www.beigebag.com/ It has quite a few tube models "built in" and is the source of the above transformer model. Cheers, Ian 

Thread Tools  Search this Thread 


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
BJT model and fT simulation with PSpice  MaxMagnificent  Solid State  4  23rd February 2011 08:30 AM 
BJT model and fT simulation with PSpice  MaxMagnificent  Solid State  0  22nd February 2011 08:16 PM 
PSPICE simulation  sunknu  Everything Else  0  21st September 2006 10:30 AM 
Pspice preamp simulation  Antonix  Tubes / Valves  8  10th January 2006 02:51 PM 
PSpice Simulation  annex666  Everything Else  1  25th November 2005 04:56 PM 
New To Site?  Need Help? 