Moving to constant-frequency ZVS - diyAudio
Go Back   Home > Forums > Amplifiers > Power Supplies

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 24th July 2005, 10:45 PM   #1
diyAudio Member
 
Join Date: Jun 2004
Location: Slovakia (middle of Europe :-))
Default Moving to constant-frequency ZVS

Hi all,
After successfully designed and build a 4kW basic full-bridge non-resonant SMPS, I would like to move further. The way to go would be a full-bridge constant-frequency phase-shift ZVS power supply controlled by UCC3895 from Unitrode (Texas Instruments)
In the document SLUU069A (http://www-s.ti.com/sc/psheets/sluu069a/sluu069a.pdf), there is a schematic of a power supply, and that would be my starting point. I understand nearly everytning, but I will need help with one, probably most important design step: Resonant components (transformer's serial inductor value and MOSFET parallel capacitors value). First, I though that we only need to connect some parallel capacitors to MOSFETs to obtain a resonant circuit with transformer's leakage inductance. But, there are no parallel capacitors in SLUU069A datasheet, but there is a 0,47uH serial inductance in series with the transformer's primary winding.
Could anybody explain these things for me, please?
  Reply With Quote
Old 25th July 2005, 02:51 AM   #2
Eva is offline Eva  Spain
diyAudio Member
 
Eva's Avatar
 
Join Date: Oct 2003
Location: Near the sea
Send a message via MSN to Eva
You should investigate further into the behaviour of your 4Kw full bridge, you will find in it the reply to your question.

Every time one switch turns off, the voltage in the corresponding side of the primary winding springs violently towards the rail opposite to the one that it was switched to. This happens because there is some energy stored in primary winding leakage inductance that has to be returned to the power supply.

If the opposite switch is turned on before all that energy is discharged, then ZVS is achieved. This requires either duty cycles approaching 100% or phase-shifted operation.

The 0.47uH inductor is here just to increase effective leakage inductance thus making its discharge time longer and making it easier to turn on the right switch in time.

There are no additional components required for ZVS operation in phase-shifted full bridges or in unregulated half/full bridges.

I feel this topic is usually misunderstood.
  Reply With Quote
Old 25th July 2005, 05:02 AM   #3
mzzj is offline mzzj  Finland
diyAudio Member
 
Join Date: Jul 2005
Location: 65N 25E
Quote:
Originally posted by Eva
You should investigate further into the behaviour of your 4Kw full bridge, you will find in it the reply to your question.

Every time one switch turns off, the voltage in the corresponding side of the primary winding springs violently towards the rail opposite to the one that it was switched to. This happens because there is some energy stored in primary winding leakage inductance that has to be returned to the power supply.

If the opposite switch is turned on before all that energy is discharged, then ZVS is achieved. This requires either duty cycles approaching 100% or phase-shifted operation.

The 0.47uH inductor is here just to increase effective leakage inductance thus making its discharge time longer and making it easier to turn on the right switch in time.

There are no additional components required for ZVS operation in phase-shifted full bridges or in unregulated half/full bridges.

I feel this topic is usually misunderstood.
I tend to disagree, capacitance IS needed for proper ZVS. In some cases mosfet internal capacitances are big enough. Without some capacitance at switch-off voltage will slew with very high speed and proper timing might be impossible for opposite switch. Also switch-off stresses for mosfet are bigger without some capacitance, with cap parallei over switch currents go trhu cap, and not ending up in swich-off losses

Extra inductance is there to ensure ZVS at lighter loads, you need certain amout of energy to load caps(mosfet internal and/or external) to archieve ZVS condition. For same reason transformer core is sometimes capped to increase magnetisation current to make ZVS possible at light loads.
  Reply With Quote
Old 25th July 2005, 05:53 AM   #4
Eva is offline Eva  Spain
diyAudio Member
 
Eva's Avatar
 
Join Date: Oct 2003
Location: Near the sea
Send a message via MSN to Eva
I hope this picture helps in understanding zero-voltage switching:

Click the image to open in full size.

It shows the turn-off process of one of the lower switches of a conventional full-bridge in an actual circuit. Switching devices are MJE13009 bipolar transistors with proportional drive. Red trace is collector voltage at 50V/div, so supply voltage was 250V. Blue trace is transformer current in 2.5A/div, so Ic was approx 6A before turn-off. Timing is 200ns/div. Power output was about 1KW when waveforms were captured. This circuit operates at 35Khz so primary leakage inductance is high, current rise and fall slopes suggest a 10uH figure.

Note how this inductance starts discharging (through the 1nF and 47 ohm RC snubber placed across the primary winding) as the switch turns off and collector voltage rises. Also note how it continues discharging through the freewheeling diode during the following 250ns.

Should the opposite switch be turned on during this 250ns period, then ZVS would be achieved since voltage drop across that switch would be very small.

However, achieving ZVS over a broad current range is a hard task since voltage rise time after turn-off is inversely proportional to primary winding current. No added combination of capacitors or inductors will solve that as slew rates are always proportional to current. The problem is actually solved by adding extra leakage inductance to the primary winding and by monitoring voltage at both ends of the bridge with comparators, so that the switches could be turned on in the right instant during discharge. I think I've seen some IC that does that.
  Reply With Quote
Old 25th July 2005, 07:15 AM   #5
mzzj is offline mzzj  Finland
diyAudio Member
 
Join Date: Jul 2005
Location: 65N 25E
Check unitrode spms seminars, best online source for these things. And even free!
http://focus.ti.com/general/docs/tra...tsp?familyId=2

http://focus.ti.com/lit/ml/slup111/slup111.pdf
http://focus.ti.com/lit/ml/slup102/slup102.pdf
http://focus.ti.com/lit/ml/slup101/slup101.pdf
http://focus.ti.com/lit/ml/slup089/slup089.pdf
http://focus.ti.com/lit/ml/slup092/slup092.pdf

Of course it can be true that almost everyone might be wrong about ZVS principles and Eva is right, altough I belive that unitrode has _some_ experience in these things...
  Reply With Quote
Old 25th July 2005, 09:12 AM   #6
Eva is offline Eva  Spain
diyAudio Member
 
Eva's Avatar
 
Join Date: Oct 2003
Location: Near the sea
Send a message via MSN to Eva
There is no statement on these papers contradicting my point of view. They just analyze and use circuit parasitistics, that's why you see additional capacitors and inductors on their theoretical schematics, but actually they don't add paralell capacitors to bridges because this dramatically increases the minimum load required for ZVS operation and reduces maximum duty cycle thus reducing efficiency. Furthermore, using paralell capacitors in constant frequency circuits or without ZVS sensing can increase losses and EMI radiation dramatically due to hard switching when the load is not high enough to achieve ZVS.

You should know that by increasing capacitance in any resonant circuit you are actually damping it and preventing it to resonate!. They also use comparators to sense zero-voltage condition and turn on the switches in the right instant as I mentioned. They don't rely on a particular resonant behavior created with additional components.

I have to emphasize: There is a lot of misunderstanding about ZVS.
  Reply With Quote
Old 25th July 2005, 09:50 AM   #7
mzzj is offline mzzj  Finland
diyAudio Member
 
Join Date: Jul 2005
Location: 65N 25E
Quote:
Originally posted by Eva

You should know that by increasing capacitance in any resonant circuit you are actually damping it and preventing it to resonate!. [/B]

Beg your pardon?
  Reply With Quote
Old 25th July 2005, 09:55 AM   #8
Eva is offline Eva  Spain
diyAudio Member
 
Eva's Avatar
 
Join Date: Oct 2003
Location: Near the sea
Send a message via MSN to Eva
Nah
  Reply With Quote
Old 25th July 2005, 12:58 PM   #9
diyAudio Member
 
John Hope's Avatar
 
Join Date: Feb 2005
Location: nr Oxford UK
Default ZVS action

I'll throw my oar into this furore in the hope that it helps.

My understanding of ZVS is that for full ZVS action to occur, a certain minimum energy is stored in the 'parasitic' inductance. This may be either the inherent leakage inductance of the trafo alone, or in combination with an additional series L to make up the necessary value. Adding an external inductance may help to achieve ZVS at lower currents, but it impacts negatively on the overall efficiency of the converter because on the power delivery cycle there is a voltage drop across the external inductance.

Also, because of the energy in an inductor being 0.5 * L * I ^ 2, the current through the switch determines the energy stored in the 'parasitic' L. This is why ZVS requires a minimum load. Where this is inconvenient, gapping the core helps, because it increases the magnetisation current. In a ZVS converter you can get away with this because you get back most of the energy due to the increased magnetisation current. The energy you don't get back is lost in the copper windings of the trafo, which needs to be generously designed.

To my mind the capacitor value does not effect the quantity of energy stored because the energy is primarily stored in the 'parasitic' inductance which then resonates with the 'parasitic' capacitance. The capacitance value will affect the frequency of resonance and hence the system timings i.t.o. dead time.

The MicroLinear Application note 19, now presented by Fairchild, is in my opinion a straightforward, simple explanation of the ZVS process for a phase shifted full bridge. It's like ZVS for dummies and I would suggest it be read before the TI articles. This app note may be found at:

http://www.fairchildsemi.com/an/AN/AN-42026.pdf
__________________
At Spes Infracta
__________________
  Reply With Quote
Old 25th July 2005, 01:32 PM   #10
mzzj is offline mzzj  Finland
diyAudio Member
 
Join Date: Jul 2005
Location: 65N 25E
Default Re: ZVS action

Quote:
Originally posted by John Hope
I'll throw my oar into this furore in the hope that it helps.

To my mind the capacitor value does not effect the quantity of energy stored because the energy is primarily stored in the 'parasitic' inductance which then resonates with the 'parasitic' capacitance. The capacitance value will affect the frequency of resonance and hence the system timings i.t.o. dead time.

The MicroLinear Application note 19, now presented by Fairchild, is in my opinion a straightforward, simple explanation of the ZVS process for a phase shifted full bridge. It's like ZVS for dummies and I would suggest it be read before the TI articles. This app note may be found at:

http://www.fairchildsemi.com/an/AN/AN-42026.pdf
I agree, cap is there A. because its parasitic piece of **** and B. you might want it to be there.
Now what i quicky found in this appnote:
"Sometimes in order to further reduce the turn-off losses
additional capacitance may be necessary across the
drain-source of each MOSFET."

Circuit working like Eva suggests(without any sort of cap) results in unneccessary turn-off losses, i.e. Ploss=0.25*U*I*Tf where U is peak voltage, I is peak current at turn-off and Tf is fall time of power switch. With something like 50ns fall times and 200khz operation these losses are easily bigger than Rds on losses.

With perfect timing it is of course possible to archieve ZVS turn-on without caps but no way to archieve "soft" turn-off. Perfect timing is hard to make work at 200khz, un-obtanium one might say. Its shoot-trough or bangbang body-diode

Eva, imagine your power switch opening lets say in 100ns with 10Amps at 400V going thru it. In middle of off-transition it has enormous peak dissipation, kilowatts in peak. Now add some capacitance across this opening switch and Voila, most of the current starts going trough this cap when you open switch and when cap is loaded to bigger voltage your switch is already completely open and not half-open.


phew. I had to find thicker wire to bend.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Moving Avatars poynton Everything Else 3 13th November 2007 08:13 PM
Hysteretic self-oscillating amplifier with constant switching frequency sovadk Class D 8 18th November 2006 10:44 AM
Hysteresis Controller with constant switching frequency TOINO Class D 4 18th June 2006 08:34 PM
Frequency CUT and a HOLE in frequency range... -_nando-_ Everything Else 0 28th December 2005 08:17 PM
Let's get the wiki moving .... paulspencer Subwoofers 0 18th October 2005 05:11 PM


New To Site? Need Help?

All times are GMT. The time now is 11:27 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2