
Home  Forums  Rules  Articles  diyAudio Store  Blogs  Gallery  Wiki  Register  Donations  FAQ  Calendar  Search  Today's Posts  Mark Forums Read  Search 

Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving 

Thread Tools  Search this Thread 
4th March 2013, 08:01 AM  #391 
diyAudio Moderator

good job rolandong......congratulations....
__________________
planet10 needs your help: Let's help Ruth and Dave...http://www.diyaudio.com/forums/plane...ml#post5010547[B 
8th March 2013, 08:54 AM  #392 
diyAudio Member
Join Date: Oct 2009
Location: Jeddah, KSA

hi tony, i have a toroid transformer taken from an old AVR rated at 1kw and I will use for transformer amp. the primary was broken so i need to wind a new one. i just want to know the number of turns on the primary at 220v and and 45v for secondary (or turns per volt). transformer sizes are 5 inch outer diameter and 3 inch inner diameter 2 inch wide.
thanks Last edited by wakwakni; 8th March 2013 at 09:07 AM. Reason: wrong spelling 
8th March 2013, 10:13 AM  #393 
diyAudio Member
Join Date: Jul 2004
Location: Scottish Borders

A core size of 1" by 2" cannot be a 1kVA transformer.
Assuming a flux of 1T you get ~120VA, at 1.5T ~180VA. Maybe you could run it @ 1.8T and get at the most 225VA. Tony, could you check my numbers?
__________________
regards Andrew T. Sent from my desktop computer using a keyboard 
8th March 2013, 11:48 AM  #394 
diyAudio Member
Join Date: Oct 2009
Location: Jeddah, KSA

avr pic
hi this is the AVR,

9th March 2013, 09:32 AM  #395 
diyAudio Member
Join Date: May 2011

Tony,
A couple of queries. I am trying to write a small program [command line type in C] to set out windings for output transformers based largely on Pat Turner's site. I am a bit confused about the difference between quiescent voltage and the maximum anode voltage on the tube [and quiescent/maximum current]. Pat Turner on his PushPull output transformer calculations Page 1  Class AB1 loadlines Figure 2 shows a *Q* current at the 500 volt mark. So his quiescent voltage and anode voltage are pretty much the same. [Also Merlin Blencowe on his website under SE Output Stage also states and highlights the fact that quiescent and anode voltage are the same based on the fact that reactive as opposed to resistive loads are being used ...]. On the other hand Steve Bench on his website under *Loadlines, Power Output and Distortion  Part 5  Establishing a loadline* is not taking quiescent as maximum anode voltage at all and has a much more sensible way it seems of establishing loadlines .. although he is actually trying to generate composite loadlines which would be next to impossible to program [for me anyway] or at the least very time consuming. Any thoughts ? My program need to ask this stuff at the beginning for it to work ie calculate the initial Class A, AB, B loadline values. Next query relates to transformers and Formulas! Ok Pat Turner works in mms and many text books are US and still use inches and furlongs. Pat Turner uses a formula as the basis for calculating the area of the transformer centre leg as A = 300*square root(P), which would be in square mms. [Pat Turner OPT calcs Page 2  Item 14] RHD4 page 235 gives a formula as A = (square root(P)) / 5.58 A is square inches. I have another book from 79 called *Practical Transformer Design Handbook* by Lowden which uses the formula as A = 0.16 * square root(P) again in square inches which sort of tallies with the one above, maybe slightly different B values were used. As I am using Pat Turner's stuff generally I can't see where his formula comes from as there are 645 square mms in a square inch. Do you use pat Turner's site to make your trannies ? I would prefer to use the original formulas rather than rough formulas for calculating areas etc. such as : P = 0.707 * J * f * W * A * B > but again there is more confusion here as some formulas lump in a figure of 10^8 such as the Lowden book on Page 58: P = 0.707 * J * f * W * A * B * 10^8 !!!!!! [this time in square cms] What is that ten to the power of minus eight figure as it does not account for different dimensions between mms, cms, inches, it is way too large. I cannot find an explanation for it ANYWHERE. Any ideas, I would like to try to reconcile a proper formula to a rough one and go from there ? Thanks 
9th March 2013, 09:38 AM  #396 
diyAudio Member
Join Date: May 2011

The figure for Power on Wiki does not include that 10^8 figure which is weird but it does include it in other calculations ... Wiki/Transformer Design/Equations page

9th March 2013, 09:46 AM  #397 
diyAudio Member
Join Date: May 2011

* WikiBooks/Electronics/Transformer Design/Equations

9th March 2013, 10:18 AM  #398  
diyAudio Moderator

donnyab,
RDH4 uses imperial units, Patrick uses cgs.... Quote:
Quote:
have you seen the book by Wolpert? it is available for download at YvesM's website... you will soon find out that formulas are fine, but actually building one and testing is even more rewarding... i just use a wire table, a pencil and paper and then i'm go......
__________________
planet10 needs your help: Let's help Ruth and Dave...http://www.diyaudio.com/forums/plane...ml#post5010547[B 

9th March 2013, 10:38 AM  #399  
diyAudio Moderator

Quote:
you are asking too much from that torroid....you need to give me the size of the core without the wires, once you have taken out the wires, measure it again and we'll see...
__________________
planet10 needs your help: Let's help Ruth and Dave...http://www.diyaudio.com/forums/plane...ml#post5010547[B 

9th March 2013, 11:32 AM  #400 
diyAudio Member
Join Date: May 2011

building one and testing one ... if I ever get that far ha ha
still trying to get my head around all the formulas .. Pat Turner I think uses a very low B figure and that would mean his transformers are much bigger, almost like he is designing them for mild steel ? so the 300 figure in his formula is probably too big by a factor of up to three thanks 
Thread Tools  Search this Thread 


Similar Threads  
Thread  Thread Starter  Forum  Replies  Last Post 
tony's 6LU8 pushpull power amp build  TonyTecson  Tubes / Valves  29  8th June 2017 11:12 PM 
Trinium, my latest build  Mark.Clappers  MultiWay  18  17th July 2012 07:07 PM 
My latest CHR70 build  tresch  Full Range  8  6th December 2011 12:34 AM 
My Latest DIY Draft (Beta) Build  Resurrected Sansui AU111  LinuksGuru  Tubes / Valves  0  27th December 2010 10:59 PM 
My latest build SS 23W  smithy666  Subwoofers  6  14th April 2009 11:50 AM 
New To Site?  Need Help? 