cheap simple way to drop 3-5v - Page 2 - diyAudio
Go Back   Home > Forums > Amplifiers > Power Supplies
Home Forums Rules Articles diyAudio Store Gallery Wiki Blogs Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 12th September 2010, 07:21 AM   #11
Elvee is offline Elvee  Belgium
diyAudio Member
Elvee's Avatar
Join Date: Sep 2006
Originally Posted by nightanole View Post
I cant unwind the transformer. Its also used in another project that needs the 35 volts. This is just me using 1 high quality power supply for 2 amps (since im incapable of listening to 2 amps at the same time).

Hmm the amp4 uses a tp2050 which has a max voltage rating of 35 volts. I might be able to just get away with replacing the 35 volt on board caps with higher voltage units.

Lets see, 2 10k high ripple caps, 1 300uf low esr cap, 2 1500uf low esr caps.
Diodes like 1N5404 are dirt cheap. They are specified for 3A continuous current, but for audio applications it's OK, as you will never draw 5A permanently.
Make a string of 8 to 12 of them, leaving the leads uncut so they can act as heatsink.
  Reply With Quote
Old 12th September 2010, 12:34 PM   #12
diyAudio Member
Join Date: Feb 2009
Man them are dirt cheap everywhere but mouser/digikey. I can get 10 for 3 bucks shipped at most places, digikey wants over 50 cents each. Another thing i found was using some 50 cent bridge rectifiers, they are 50 cents each and drop at least a volt.

Well thanks guys for shooting me some ideas.
  Reply With Quote
Old 12th September 2010, 02:52 PM   #13
diyAudio Member
Speedskater's Avatar
Join Date: Sep 2002
Location: Lakewood, Ohio
I would think that adding a small boost/buck transformer is easier than rewinding the main transformer.
  Reply With Quote
Old 12th September 2010, 02:55 PM   #14
diyAudio Member
Join Date: Nov 2005
Not if it's a toroid. A toroid is just sitting there waiting for you to put a buck winding on it. You don't need another primary and another core.
  Reply With Quote
Old 12th September 2010, 04:07 PM   #15
star882 is offline star882  United States
diyAudio Member
star882's Avatar
Join Date: Mar 2007
You can also use a buck converter.
"Fully on MOSFET = closed switch, Fully off MOSFET = open switch, Half on MOSFET = poor imitation of Tiffany Yep." - also applies to IGBTs!
  Reply With Quote
Old 13th September 2010, 01:54 PM   #16
diyAudio Member
Join Date: Aug 2010
Location: Adelaide
Just another alternative: a simple high current customisable regulator Pre-Regulator
  Reply With Quote
Old 13th September 2010, 02:10 PM   #17
AndrewT is offline AndrewT  Scotland
diyAudio Member
Join Date: Jul 2004
Location: Scottish Borders
a capacitor multiplier gives a near fixed voltage drop across it.

If you adjust the resistors you can dial up just about any voltage drop.

Normally a multiplier is used with just 1.5V to 2.5V drops to allow for ripple when high currents are demanded.

But they work just as well when set up to drop more voltage.
But, then they dissipate more power. You will need heatsinks on the power output devices.
regards Andrew T.
Sent from my desktop computer using a keyboard
  Reply With Quote


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off

Similar Threads
Thread Thread Starter Forum Replies Last Post
5v to 2.5v for 2a3 filament gasser-dude Tubes / Valves 7 13th February 2010 09:18 AM
What do you use for a simple cheap load? digital desire Solid State 30 30th December 2006 10:04 AM
Simple and cheap sparkle Solid State 33 14th May 2004 05:19 PM
Can you make 0-5V DC out of 2.5-0-2.5V AC Ralph Tubes / Valves 17 23rd September 2003 03:20 PM

New To Site? Need Help?

All times are GMT. The time now is 05:28 PM.

vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright 1999-2017 diyAudio

Content Relevant URLs by vBSEO 3.3.2