Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Have 7v ac need 6.3v ac, need simple ideer
Have 7v ac need 6.3v ac, need simple ideer
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 17th June 2010, 06:43 AM   #1
heinrichs is offline heinrichs  Denmark
diyAudio Member
 
Join Date: Jul 2009
Default Have 7v ac need 6.3v ac, need simple ideer

Hello

i am building a tube amp, where i need around 15A for the heaters, which run at 6.3V..

but.. the power trafo i have, is abit old, so it was made for 220V, but i have 230-240V in my outlet, so all the outputs are just abit higher then what is printed on the trafo.

so now i have a 7Vac where i need a 6.3Vac.

i could use a resistor in series.. but that would have to disipate 10W....

could maybe do something with some diodes.. but is there diodes that can take the current, and in a package that is suitable for some cooling?

the power supply will be powering 2 seperate monobloks, so would be nice if the voltage wasnt load dependent which it will be with the resistor..

i am thinking the resistor is the best ideer... but there could very well be a super simple ideer i just havent thought of, so i though i would ask in here :-)

regards
Jens

Last edited by heinrichs; 17th June 2010 at 06:50 AM.
  Reply With Quote
Old 17th June 2010, 06:53 AM   #2
SemperFi is offline SemperFi  Wake Island
diyAudio Member
 
Join Date: Jan 2002
Location: nowhere
Have you tested the voltage with a load that draws 15A?
  Reply With Quote
Old 17th June 2010, 07:27 AM   #3
east electronics is offline east electronics  Greece
diyAudio Member
 
east electronics's Avatar
 
Join Date: Jan 2006
Location: Athens GREECE
that is correct ...voltage will drop no matter what with 15A load .... even possible that it drops more than needed ....
__________________
SERVICE ΕΝΙΣΧΥΤΩΝ ΚΑΙ ΙΑΠΩΝΙΚΩΝ ΜΗΧΑΝΗΜΑΤΩΝ ΗΧΟΥ www.eastelectronics.gr
  Reply With Quote
Old 17th June 2010, 07:28 AM   #4
gmphadte is offline gmphadte  India
diyAudio Member
 
Join Date: Jul 2003
Location: Dona paula, Goa
Put two antiparallel diodes in series. This will reduce 0.6 volts

Gajanan
  Reply With Quote
Old 17th June 2010, 07:29 AM   #5
heinrichs is offline heinrichs  Denmark
diyAudio Member
 
Join Date: Jul 2009
offcourse... just didnt think about that... normally i use switchmodes for everything....

gonna do some measurements when i get home from work today, thanks :-)

#4
just have to be some pretty big diodes... but should work though..
  Reply With Quote
Old 17th June 2010, 07:43 AM   #6
Elvee is offline Elvee  Belgium
diyAudio Member
 
Elvee's Avatar
 
Join Date: Sep 2006
The diodes will work, but they will dissipate exactly the same power as the resistor.
In addition, they will generate severe harmonics and switching noise.

Of course, if your wiring is absolutely perfect, this doesnt matter, but.....

If you want a solution that is both non-dissipative and "quiet", you could use a series inductor: in this case, 150ÁH would do the trick (it obviously has to be rated for 15A).
It will not only adjust the voltage to the correct level, but also somewhat soften the cold start, and improve the noise filtering.
  Reply With Quote
Old 17th June 2010, 09:04 AM   #7
AndrewT is offline AndrewT  Scotland
diyAudio Member
 
Join Date: Jul 2004
Location: Scottish Borders
connect up your 15A worth of heaters and measure the voltage across the heater pins, before you do anything else.

If you want to draw a continuous 15Aac from your transformer, the secondary winding must be rated >=15Aac and preferably >=30Aac, (200VA). What size is your transformer?
__________________
regards Andrew T.
  Reply With Quote
Old 17th June 2010, 01:46 PM   #8
heinrichs is offline heinrichs  Denmark
diyAudio Member
 
Join Date: Jul 2009
I ended up puttig my heaters in paralel 2 by 2, since i have multiple 6.3v outputs on my trafo, so i could connect them making 14Vac.

and then i found some 160ÁH 6A inducters, and 2 of them in series for each mono blok does the trick.

thank you all for your help.
  Reply With Quote

Reply


Have 7v ac need 6.3v ac, need simple ideerHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
12V AC to 6.3v DC simple supply for idiots DrewP Tubes / Valves 12 14th September 2009 02:06 AM
How easy is it to convert from 110V AC to 240V AC? spikeyfaz Analog Line Level 19 26th December 2007 07:14 PM
WTB: Analog AC Ammeter - AC Voltmeter - Panel Mount dBfreak Swap Meet 1 16th March 2007 10:41 PM
PS question- Need to get 20V AC from 60V AC - w/o Trafo lgreen Pass Labs 9 2nd January 2004 10:31 AM
HUBBELL IG3800 clones? AC sockets /AC wire jasonruiz Parts 5 25th April 2003 10:21 PM


New To Site? Need Help?

All times are GMT. The time now is 10:00 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio
Wiki