spike problem ! - Page 2 - diyAudio
Go Back   Home > Forums > Amplifiers > Power Supplies

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 29th March 2010, 09:33 PM   #11
diyAudio Member
 
Join Date: Nov 2004
Location: Bucharest
top pictures are without snubber
whit snubber 22nF + 10 ohm/3w on primary (not GND), whit no load.
Attached Images
File Type: jpg 1.jpg (58.1 KB, 107 views)
File Type: jpg 2.jpg (67.3 KB, 105 views)
File Type: jpg 3.jpg (494.3 KB, 102 views)

Last edited by mgm2000ro; 29th March 2010 at 09:41 PM.
  Reply With Quote
Old 29th March 2010, 09:35 PM   #12
diyAudio Member
 
Join Date: Nov 2005
What's the deal with the first and third waveform shots you last posted? Presumably those are both sides of the push-pull? The last one looks passable. If you have the same circuit and are getting different results, then you don't have the same circuit. The layout must be an issue.

(well I meant the post before the last)

Last edited by Andrew Eckhardt; 29th March 2010 at 09:37 PM.
  Reply With Quote
Old 29th March 2010, 09:39 PM   #13
diyAudio Member
 
Join Date: Nov 2004
Location: Bucharest
Whit the same pcb and irfp1405 the problems is gone!
I guess my problems is the large input capacitans of irfp2907pbf.
What can I do?
  Reply With Quote
Old 29th March 2010, 09:41 PM   #14
diyAudio Member
 
Join Date: Nov 2005
Can you post an overlay of the gate and drain waves for one FET?
  Reply With Quote
Old 29th March 2010, 09:48 PM   #15
diyAudio Member
 
Join Date: Nov 2004
Location: Bucharest
wave form pin 1-3 mosfet
Attached Images
File Type: jpg 4.jpg (69.6 KB, 87 views)
  Reply With Quote
Old 29th March 2010, 10:02 PM   #16
diyAudio Member
 
Join Date: Nov 2005
I meant can you post a shot of gate and drain pulses on one oscillogram. I'm trying to figure out exactly what's starting to happen 1uS after the rising edge of the drain voltage. Try the gate of one side drive and the drain of the other.
  Reply With Quote
Old 29th March 2010, 10:21 PM   #17
diyAudio Member
 
Join Date: Nov 2004
Location: Bucharest
wave form yellow pin 1-3 (mosfet-1) blue pin 2-3 (mosfet-2)
Attached Images
File Type: jpg 5.jpg (125.1 KB, 87 views)
  Reply With Quote
Old 29th March 2010, 10:39 PM   #18
diyAudio Member
 
Join Date: Nov 2005
I think your turn-off/on might be too fast for these big transistors.
  Reply With Quote
Old 29th March 2010, 10:44 PM   #19
diyAudio Member
 
Join Date: Nov 2005
Does increasing dead time not help at all?
  Reply With Quote
Old 29th March 2010, 10:51 PM   #20
diyAudio Member
 
Join Date: Nov 2004
Location: Bucharest
I'll come back with changes tomorrow. Thank you very very much!
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
current spike question foobar Solid State 2 14th December 2008 07:49 PM
spike from SG3525 jegandren Power Supplies 7 13th September 2008 03:23 PM
no spike protection allowed tryonziess Chip Amps 6 13th May 2007 05:52 PM
Speaker Spike bjackson Multi-Way 8 9th May 2005 01:12 AM
Anyone use these Spike Feet? m1abrams Multi-Way 2 22nd July 2004 06:54 PM


New To Site? Need Help?

All times are GMT. The time now is 03:23 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2