Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

PS Problem: How do I Reduce Voltage?
PS Problem: How do I Reduce Voltage?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 26th April 2008, 06:00 AM   #1
slor is offline slor  United States
diyAudio Member
 
Join Date: Jul 2007
Default PS Problem: How do I Reduce Voltage?

I'm working on an active tube DI, based on the Altec 1566A:

Click the image to open in full size.

I had to sub out the power transformer, but the new one is fairly close to the one called out in the schematic: It puts out 120VAC at 93 mA, and the filament is 6.3VAC at 1A. I'm inexperienced at best, but I did follow the schematic and the connections etc. are all good.

The filament side is fine, a little high at 6.8VDC but that seems at least in the ballpark. The problem is the B+; even bumping R9 up to 9500ohms, the lowest voltages I can get are 345VDC at "2" and 240VDC or so at "1."

In short: HELP!!!!!!!!!!!

I'm assuming I'm going to need to introduce a regulator of some kind; I have a spare LM350 but I need a plan!

-Seth
  Reply With Quote
Old 26th April 2008, 06:33 AM   #2
Miles Prower is offline Miles Prower  United States
diyAudio Member
 
Miles Prower's Avatar
 
Join Date: May 2005
Location: USA
^^^^

Since it's a voltage doubler circuit:

2(120 * sqrt(2)))= 339.4Vdc

That's reasonable for this circuit. I wouldn't worry much about it since the load will pull the voltage down a bit, especially since RC filter sections are included for ripple filtration.
__________________
There are no foxes in atheistholes
www.dolphin-hsl.com
  Reply With Quote
Old 26th April 2008, 11:23 AM   #3
tubewade is offline tubewade  United States
diyAudio Member
 
tubewade's Avatar
 
Join Date: Jun 2007
The voltages shown on the schematic are what you should find with a load. If your measurements are without a load I expect all is well.
  Reply With Quote
Old 26th April 2008, 12:22 PM   #4
lcsaszar is offline lcsaszar  Hungary
diyAudio Member
 
Join Date: Mar 2004
Location: Budapest, Hungary
The voltage rating of C6 should be higher than the unloaded B+ voltage. If you use the common 350V capacitor, there is a risk. Go for 450V if you want to be in the safe area.
  Reply With Quote
Old 26th April 2008, 05:20 PM   #5
slor is offline slor  United States
diyAudio Member
 
Join Date: Jul 2007
Default No, this is loaded!

Thanks for the replies gents; I should have specified: The voltages I'm getting are with tubes installed!

Click the image to open in full size.


And thanks oshifis, the filter caps are F & Ts rated at 500 I believe....
  Reply With Quote
Old 27th April 2008, 05:41 AM   #6
slor is offline slor  United States
diyAudio Member
 
Join Date: Jul 2007
Default Almost Forgot...

The "120VAC" transformer actually puts out 146VAC, a least unloaded. Is this so far off spec to be worthy of return or replacement? Still seems there's other issues at play here, but....
  Reply With Quote
Old 27th April 2008, 06:15 AM   #7
sorenj07 is offline sorenj07  Germany
diyAudio Member
 
sorenj07's Avatar
 
Join Date: May 2006
Location: Berlin
That is very weird. Have you tried switching the "120V" taps for each other?
  Reply With Quote
Old 27th April 2008, 03:18 PM   #8
slor is offline slor  United States
diyAudio Member
 
Join Date: Jul 2007
Hmm...no. I suppose it couldn't hurt. But either way, something seems real off here. Supposedly:

2(146 * sqrt(2))= 412Vdc

which is actually just about what I got with the PT unloaded.

I'm just trying to figure out if this transformer is going to work at all or if there's a way to lose 25V or so right off the bat....

-Seth
  Reply With Quote

Reply


PS Problem: How do I Reduce Voltage?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
how to reduce PSU DC voltage space2000 Solid State 11 18th May 2008 10:12 AM
Voltage divider to reduce 6v dc to 2vdc duderduderini Tubes / Valves 5 26th February 2008 09:28 PM
How to reduce voltage from PSU?? oblerum Power Supplies 4 10th August 2006 07:04 AM
Reduce wallwart voltage argonrepublic Parts 2 19th February 2006 02:51 PM
Help:How To Reduce Transformer Output Voltage? phill77 Solid State 0 21st April 2003 12:04 PM


New To Site? Need Help?

All times are GMT. The time now is 12:26 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio
Wiki