Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Planars & Exotics ESL's, planars, and alternative technologies

Acoustat 1+1 weak output
Acoustat 1+1 weak output
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 21st December 2006, 03:23 AM   #1
danielm is offline danielm  United States
diyAudio Member
 
Join Date: Dec 2006
Default Acoustat 1+1 weak output

They have been unhooked for four yrs. I bought them new and always had plenty of output. Now I find them weak, very weak.
As if the PS has failed. But both of them ???

I pulled down one sock and had a look at the panels. No arcing, holes or loose film.

What now?

BTW, there is a place just up the road that makes mylar film. I see rolls of the stuff in the dumpster at times.
I may stop and check it out next time.
I always wanted to DIY some ESLs.

Regards,
Daniel
  Reply With Quote
Old 21st December 2006, 03:59 AM   #2
SY is offline SY  United States
On Hiatus
 
SY's Avatar
 
Join Date: Oct 2002
Location: Chicagoland
Acoustat 1+1 weak output
I'd double check all the connections inside the interfaces and the fuses. You could also have corroded connections to the diaphragm.
__________________
"You tell me whar a man gits his corn pone, en I'll tell you what his 'pinions is."
  Reply With Quote
Old 21st December 2006, 04:09 AM   #3
danielm is offline danielm  United States
diyAudio Member
 
Join Date: Dec 2006
I'm surprised I have this problem. Last yr I pulled some Maggies out of the closet to find the HF aluminum had... decomposed.
Now this.
I guess I can't complain since the're what 20+ yrs old now.

I'll open up the interface and see what I find.

Any suggested mods while I'm there?
  Reply With Quote
Old 21st December 2006, 12:15 PM   #4
SY is offline SY  United States
On Hiatus
 
SY's Avatar
 
Join Date: Oct 2002
Location: Chicagoland
Acoustat 1+1 weak output
Mods to the interface have been discussed here before- do a search and you'll find all kinds of fun things to do. But... I'd get them working stone-stock first.

From your Maggie story, I'll bet that you find that the diaphragm contact has gone to meet its Maker.
__________________
"You tell me whar a man gits his corn pone, en I'll tell you what his 'pinions is."
  Reply With Quote
Old 21st December 2006, 12:49 PM   #5
enilsen is offline enilsen  Sweden
diyAudio Member
 
Join Date: Oct 2006
Default Hv bias failure to diaphram

I came across a similar problem about 3 years ago when I took my Martin Logan CLS speakers out of 10 years of storage. The sound was very weak from both panels and I did all sorts of things to try and get them working again. I was told that new panels were the only way to get it working again.

I felt that the replacement with new panels was not the solution to the problem rather than a quick fix because nobody would give me a logical answer to what the problem was.

Anyhow to cut a long story short I believe problem is something similar to what happens to aging capacitors. The diaphragm coating and the high-voltage bias contact has had some chemical degrading and eventually the hv bias current no longer is conducted to the diaphragm.

The way I could determine this was to use a plant sprayer and spray a small amount of water onto the diaphragm near the hv bias connection. The sound would then return like magic and would vanish in a couple of days when the water had evaporated.

The final fix for this problem was to use an eye dropper with diluted liquid soap (conductive) and apply a very small amount on the diaphragm. This would run down the diaphragm and make contact with the hv bias metal strip. The hv bias connection was restored and the speakers have worked ever since.
  Reply With Quote
Old 21st December 2006, 03:26 PM   #6
danielm is offline danielm  United States
diyAudio Member
 
Join Date: Dec 2006
Hmm... a lossy (resistive) connection to the panel...
I could understand that on the low impedance of the Maggies but for the esl panels to be this weak it must be damn near open.

I noticed acoustat has run all three panel wires together up one side. It seems to me that the diaphagm wire could go down the opposite side. The added capacitance of those wires bundled together coud be eliminated.

I'm sure my supplys are ok as the diaphragm slapped the stator when I plugged them in.

I'll start digging this weekend.

Thanks,
Daniel
  Reply With Quote
Old 22nd December 2006, 04:32 PM   #7
danielm is offline danielm  United States
diyAudio Member
 
Join Date: Dec 2006
I'm beginning to think it is a bias voltage issue on the diapragm.
Looking inside the MK121 interface I see no obvious problems. Bias voltage seems to be good to the "red" wire leading to both panels.
I fed a 400hz sine wave and made some measurements using a DVM.
With 8VAC input to the binding post I measured approx 600VAC on the stator wires. (the upper ac limit of my meter)
With a >250hz sine wave the sound appears loud.
There's audable distortion begining at 11VAC input below 200HZ. At 400HZ it is fine sounding up to 40VAC input. I am using a large QSC power amp so, this test was brief. I never saw arcing.
At 40hz the panel starts to rattle at an input of 11VAC.
I cannot figure out why they have little output with music but the 400hz tone sounds loud.
It sounds as if the panel's bias voltage is collapsing with bass transients.
I see no way to to check or fix the bias connection to the panels.
Is this a common problem for 20 yr old Acoustat panels?
  Reply With Quote
Old 23rd December 2006, 02:48 AM   #8
bear is offline bear
expert in tautology
diyAudio Member
 
bear's Avatar
 
Join Date: Apr 2002
Location: New York State USA
Acoustat 1+1 weak output
This problem has been discussed several times recently... do a search and look down the subject rows a bit for other Acoustat threads??

The cause of low output on the Acoustats is usually a bad diode or cap in the HV multiplier.

The way to test it is with a HV probe on a suitable meter.
The proper HV is ~5kv and not too much lower.

It is simple enough and cheap enough to pull the board and buy some high voltage diodes - higher is better, 2kv being ok in general, and some high voltage rated ceramic caps, take the old ones out, solder the new ones in. Done.

Nothing else will go bad on BOTH cells on BOTH channels, unless the panels have been somehow exposed to a highly corrosive environment for a long time... but then you should see some light through the black part of the mylar coating, AND see rust and corrosion elsewhere.

Sometimes it will take 24hrs to reach full charge on an Acoustat, although it should make decent sound right away.

Change the electrolytic coupling caps to FILM caps asap for best overall sound and sound stage. <--- free advice dept, unrelated to ur problem.

_-_-bear
__________________
_-_-bear
http://www.bearlabs.com -- Btw, I don't actually know anything, FYI -- every once in a while I say something that makes sense... ]
  Reply With Quote
Old 27th December 2006, 07:07 PM   #9
danielm is offline danielm  United States
diyAudio Member
 
Join Date: Dec 2006
OK, I'm going to pick up some parts this week to make a HV probe if I get a chance. Might as well get some 1N4007s as well.

But, I have this gut feeling the panels are loosing their conductivity. Mist from a plant sprayer was an easy enough test and resulted in a bit more output.

I don't see how to get to the bias connection on the film.

SY, is this the "corroded connection" you are refering to?

I'll make some spl checks at 1m with 2.83volts. Maybe the corroded connection is between my ears.
  Reply With Quote
Old 27th December 2006, 08:14 PM   #10
SY is offline SY  United States
On Hiatus
 
SY's Avatar
 
Join Date: Oct 2002
Location: Chicagoland
Acoustat 1+1 weak output
Quote:
SY, is this the "corroded connection" you are refering to?
Yes. Likewise, you could also snoop around for any leakage between the diaphragm and ground.
__________________
"You tell me whar a man gits his corn pone, en I'll tell you what his 'pinions is."
  Reply With Quote

Reply


Acoustat 1+1 weak outputHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
NAD 3240PE VERY weak right channel danter Solid State 1 14th January 2008 03:43 PM
Help! Weak Bass! TubeHead Johnny Tubes / Valves 19 10th October 2007 09:36 PM
why am I getting weak sub output? pasomark Subwoofers 18 21st December 2005 05:58 PM


New To Site? Need Help?

All times are GMT. The time now is 07:53 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio
Wiki