Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Planars & Exotics ESL's, planars, and alternative technologies

Help - JansZen Z-600 - dead step-up transformer?
Help - JansZen Z-600 - dead step-up transformer?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 19th April 2006, 09:52 PM   #1
centaurus3200 is offline centaurus3200  United States
diyAudio Member
Join Date: Apr 2005
Location: oakland
Default Help - JansZen Z-600 - dead step-up transformer?

hi all,

my friend and i now have all new capacitors, resistors and diodes in each speaker. nothing old except for the drivers and the power supply transformers.

well, same deal as before. one speaker sounds incredible and the other's electrostatic panels are faint sounding. we swapped the panels. the "faint' ones come alive in the other speaker. so, they are okay.

so, i guess that leaves the voltage step up transformer, right? we didn't check the voltage with a multimeter. were a little scared of getting knocked out with 1,100 volts ;-)

any advice would be greatly appreciated. this is a major bummer because the one working speaker, complete with AR2 woofer sounds downright incredible. it's just teasing me with the notion of having a stereo pair of these bad boys running on a diet of McIntosh MC60 tube power

anybody got a spare power supply?

  Reply With Quote
Old 5th May 2006, 06:19 PM   #2
bear is offline bear
diyAudio Member
bear's Avatar
Join Date: Apr 2002
Location: New York State USA
This is simple enough.

You need to measure the good transformer - not the whole supply.

How to:

Remove the secondary wires going to the diodes - it's either 2 or 3 wires. Place a 12vac transformer's secondary on the primary of the good transformer. Measure the 12vac transformer's actual voltage when running and connected to the 120vac input of the "good transformer (GT)". That's where it would have been plugged into the wall, ok?

Now we measure the secondary votage of the GT!

[wall AC]--->[120v in - 12 vac out xfrmr](test voltage A)--->[Janzen GT in - seconday out] --->(test voltage B)

This tells us the voltage/turns ratio of the power transformer!

If you have used a transformer for this test that is 12vac or pretty close, you can just multiply the voltage you measured on the secondary of the GT by 10. Now you know the secondary voltage you need to replace the transformer!!

I'd order two and replace both. You only need something that is +/- 10-15% of the original values - the size of the thing is largely irrelevant as no current is drawn, so it can be considerably larger and somewhat smaller (usually) in core size.

It's likely something in the 250-500vac range depending on the number of diodes used in the mulitiplier stack, and the final bias voltage.

( ...you could always add another stage to the stack and use a lower voltage transformer, fwiw)

Which, brings us to the main question - did you change or check the caps and diodes in the voltage multiplier stack?? More likely than not you've got a shorted/leaky little ceramic cap there, and/or a dead diode.

Test the presumed bad transformer the same way. That will tell you if it is the xfrmr or the diode mulitiplier stack!

http://www.bearlabs.com -- Btw, I don't actually know anything, FYI -- every once in a while I say something that makes sense... ]
  Reply With Quote
Old 5th May 2006, 06:35 PM   #3
centaurus3200 is offline centaurus3200  United States
diyAudio Member
Join Date: Apr 2005
Location: oakland
thanks bear. will do!

there are NO original caps, resistors or diodes left in either speaker.

i will let you know!

  Reply With Quote


Help - JansZen Z-600 - dead step-up transformer?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY step down transformer rhapsodee Parts 4 24th May 2009 03:16 AM
Step Down Transformer Ropie Power Supplies 3 15th October 2006 09:42 AM
Can I use a step-up transformer as step-up? cviller Parts 5 6th September 2006 06:32 PM
Using one transformer to step down another. Shoog Solid State 9 28th August 2003 10:00 PM

New To Site? Need Help?

All times are GMT. The time now is 03:29 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio