Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Planars & Exotics ESL's, planars, and alternative technologies

Repairing Tannoy "System 1000" HF drivers
Repairing Tannoy "System 1000" HF drivers
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 11th March 2011, 12:36 PM   #1
PhantomBox is offline PhantomBox  Venezuela
diyAudio Member
Join Date: Jan 2008
Default Repairing Tannoy "System 1000" HF drivers

I have these Tannoy "System 1000" speakers from a friend on my desk with blown HF (high frequency, "tweeters") drivers.
The first time only one HF driver went bad so I replaced it with a new one that my friend bought on ebay for US$75,-- + s&h.
Now with both drivers blown I asked him to bring his power amp to check if anything might be wrong with it. Well, it was set in "mono bridge" mode. I'm not sure if this means anything, but this time I tried to fix the HF drivers by myself.

On the 1st driver, I carefully detached the windings from the coil (19 windings, to be exact, no continuity measured) and replaced them with a new piece of wire and glued it in place (again 19 windings or 1,61 meter, this time 4,5 ohms measured, same as on the woofers). And the driver actually worked!

On the 2nd driver, when I tried to (carefully) detach the windings from the coil (small rectangular plastic band bonded around the diaphragm) it itself got detached.

And here is my question: Is there a special secret way to reattach this plastic band around the diaphragm?
And what type/kind of readily available glue would you suggest?
To hold the wire in place I used "LOCTIDE Super Gel Bonder" (slow curing super glue). But since there is a tension on the plastic band that pushes it open, this glue won't work here. Regular super glue won't work either because its to aggressive and gets too hard in an instance.

Thanks in advance for any help.
  Reply With Quote
Old 11th March 2011, 09:53 PM   #2
geraldfryjr is offline geraldfryjr  United States
diyAudio Member
Join Date: Feb 2008
Location: Jackson,michigan
try a slow to medium setting epoxy. jer
  Reply With Quote
Old 11th March 2011, 10:08 PM   #3
pinkmouse is offline pinkmouse  Europe
diyAudio Moderator
pinkmouse's Avatar
Join Date: Apr 2002
Location: Rotherham, England
Repairing Tannoy "System 1000" HF drivers
Make yourself a jig. Sand down a piece of dowel held in a pillar drill so it's a tight fit in the good voice coil former, round the end off so it fits in the dome, then hold the split voice coil former onto the dowel with rubber bands whilst you glue. Then you can use the dowel to rotate the VCF whilst you wind the new VC.
Rick: Oh Cliff / Sometimes it must be difficult not to feel as if / You really are a cliff / when fascists keep trying to push you over it! / Are they the lemmings / Or are you, Cliff? / Or are you Cliff?
  Reply With Quote
Old 14th March 2011, 02:44 PM   #4
PhantomBox is offline PhantomBox  Venezuela
diyAudio Member
Join Date: Jan 2008
Default Repairing Tannoy "System 1000" HF drivers

I finally recoiled both HF drivers. After rebuilding the 1st one, the 2nd wasn't that hard. Although both sound slightly different I prefer to leave them the way they are.
I still have one doubt: One driver measures 4.5 ohms and sounds slightly louder than the other one that measures 4.0 ohms. That's aprox. 12.5%. Shouldn't it be the opposite?
  Reply With Quote


Repairing Tannoy "System 1000" HF driversHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
"Small" enclosure for Tannoy 15" andersen09 Multi-Way 36 28th June 2012 06:34 PM
An unusual "feature" on a commercial amp... crosscoupling between channels at hf. Mooly Solid State 1 1st February 2010 09:13 AM
Building a 2.1 system out of a 48"x96" sheet of 3/4" MDF 454Casull Multi-Way 0 18th November 2008 02:19 AM
Karlson "projectors" and HF waveguide tubes freddi Multi-Way 3 9th December 2007 09:47 PM

New To Site? Need Help?

All times are GMT. The time now is 04:00 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio