Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Planars & Exotics ESL's, planars, and alternative technologies

Open baffle vs ESL?
Open baffle vs ESL?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 19th December 2010, 01:03 PM   #1
Ridin '24'z is offline Ridin '24'z  United Kingdom
diyAudio Member
Join Date: Aug 2006
Default Open baffle vs ESL?

Hey all I wanted to throw this out there to see what people think on which of these technologies have the best all round performance.

I'm currently torn between two designs:

1) A 250mm by 1000mm curved ESL system
2) A 330mm by 1000mm tall open baffle system using two Alpair 10 full range drivers each side.

Both will utilise a sealed sub at the bottom. As much as I want to make both, I only have time/funds for one right now.

The open baffles will be powered at 25W per driver (i.e. 50W per side not including sub). My question is, what levels of volume will I be getting with esls this size in comparison to the open baffles? I will normally listen to them at comfortable volumes, but I will need to be able to crank it to high levels when doing things around the house. I can't really make anything wider than 1ft as that will start compromising the free space available around the baffle as well as WAF .

I'm not too worried about compromising sound between these two systems for practicality and reasonable spl .
  Reply With Quote
Old 19th December 2010, 03:27 PM   #2
Keith Taylor is offline Keith Taylor  Australia
diyAudio Member
Join Date: Nov 2007
Location: Adelaide
Open baffle vs ESL?
Using two full range drivers on a baffle is not a good idea as the high frequency vertical directivity will be very listening angle dependant. Smooth directivity calls for an acoustically small source.

Acoustically small means that the dimensions of the source are to be preferably less than the wavelength at the highest frequency of interest. The wavelength at 10 kHz is 34.4mm, which explains why a 25mm dome tweeter is often used.

You will have two tweeters spaced around 11 inches? apart resulting in the vertical pattern deteriorating above about 1.5kHz. This will result in a very narrow listening window where you will have to find a chair that puts your ears at the mid point of the two drivers!

Of course these remarks apply equally to ESL's, the difference being that the ESL is to be viewed as a line source over most of its range. Thus the high frequency pattern will be consistent between the floor and the height dimension of the ESL. Sorry to be the bearer of bad news, but physics will have its way.

  Reply With Quote
Old 19th December 2010, 09:58 PM   #3
speedracer5 is offline speedracer5  United States
diyAudio Member
Join Date: Nov 2004
Location: Ohio
For open baffle I recommend the Tang Band 1808 full range driver in the upper 1/3 of a 28-32 inch wide baffle which may or may not be tapered. About 40-48 inches tall tilt back about 3-5 degrees. For arranging an integral open baffle sub woofer look at this V-2 - V-2

There are a lot of open baffle on the GR-Research site. Since hearing the Tang Band 1808 I think it is a very smooth and non fatiguing sounding driver, and really nice bass for an 8 inch OB. It is much less expensive than the coaxial driver GR-research sells.

As for ESLs I happen to love old Acoustats but they are a handful when there are problems with the panels and power interface. They also need a high current amp or to be driven with the Acoustat Servo Drive tube amps, in which case then the "care and feeding" goes up another few notches. Many are swearing by the DIY approach to ESL's and I don't discourage but that is a bit of work to get right. There are nevertheless plenty of threads here to get you through the rough spots.

Agree with Keith that two full rangers separated by a large amount would not be good. The single Tang Band will get your ears to bleed SPL wise. Only the lowest octave needs to be reinforced with a sub preferably an OB set like the link above. I heard the Tang Band in a 3 foot wide by 4 foot tall piece of MDF propped up with fir strips in my living room driven by a Nelson Pass J2 and it was nothing short of stupid good. $400 worth of drivers slapped into a board and thats it. The bass would be fine for all but the most demanding music in a modest sided room. Pretty incredible.

Last edited by speedracer5; 19th December 2010 at 10:06 PM.
  Reply With Quote
Old 19th December 2010, 11:53 PM   #4
Ridin '24'z is offline Ridin '24'z  United Kingdom
diyAudio Member
Join Date: Aug 2006
Thanks Keith, I didn't realise that would be a problem. I suppose one full range driver per side with some kind of sub will be fine. As for the Tang Band 1808 full range driver, any idea of availability and cost in the UK?

I have a variable ESL supply already and a couple 400W tripath amps that should get me up and running for now. I have built a set of small wire stator ESLs before and they worked but weren't the best design. I've got a new design that's based on the Martin Logan curved design and should be more promising. Need to find/make the transformers though.

I have no idea in what ESLs compare to open baffles in SPL. The Martin Logan ESLs spec around 90 - 94dB which is promising.

If I do an open baffle design, I don't want to go more than 1 foot in width. These speakers will have to sit between a chimney and a wall next to the mantle piece of a fire place and any wider will make the speakers too close to the adjacent walls. How much of a wing would I be able to add to keep the sound open enough?

As for the sub, I'm looking towards a sealed sub but would OB subs give enough for the size? What about a W frame dipole sub?
  Reply With Quote
Old 19th December 2010, 11:57 PM   #5
a.wayne is offline a.wayne  United States
Sin Bin
Join Date: May 2008
Location: Front Row Center
I would do the ESL, if you are serious about doing an open baffle speaker it will have to be done correctly , done so it can rival the ESL for transparency and dynamics, with better bass ( vented bass enclosure ) .

  Reply With Quote
Old 20th December 2010, 07:41 AM   #6
Calvin is offline Calvin  Germany
diyAudio Member
Calvin's Avatar
Join Date: Nov 2004
Location: close to Basel

if done right, the ESL will outperform any dynamic driver.
In Your case this means though to accept some restrictions. A panel of the suggested size should be crossed over not below 300Hz. Itīll be no easy task to find a matching bass partner. As Keith already mentioned the distribution character of the panel differs greatly to a dynamic FR driver and the dynamic bass. In comparison the greater the listening distance the louder the panel will play. The dynamic OB will be loudest in close distance, quickly loosing SPL over distance. Same holds true for the bass, but matters are less serious here, because of the room acoustics somewhat counter the effect.

How much SPL You can get, depends on basically three factors:
1: Listening distance and room acoustics
2: Panel construction and distribution character
3: Impedance of the panel

1) A strip shaped thin and high panel is a longthrow device. The SPL-distribution over distance is far more even than with other shapes or drivers.
2) The panel needs to be constructed as eficient as possible, meaning smallest stator-stator-distances and highest mechanical diaphragm tension as possible. These are the most decisive factors in panel construction anyway. Forget FR-ESLs here.
3) Finding the right audio transformer is a compromise-game again.
Higher transformation factors donīt increase SPL much, but effect the load the amplifier needs to drive on a much greater scale. Itīs more important to find a good match between the panelīs requirements and the amps capabilities.

If done right, You can ecpect >90dB@2.83V@4m for a panel of the suggested size. This doesnīt sound much at first glance, but theoretically You need to add 12dB compared to a standard measurement in 1m distance for a global distributing driver (pulsating sphere). In praxis 6-8dB are left. You can add a further 2-3dB in comparison to dynamic drivers, because of the absence of power compression/heat losses.
So You donīt need high wattage specced amps. 20-50W@8Ohms are more than sufficient if the amp works stable.

  Reply With Quote
Old 20th December 2010, 02:37 PM   #7
Ridin '24'z is offline Ridin '24'z  United Kingdom
diyAudio Member
Join Date: Aug 2006
I think I will concentrate on ESLs then. I was planning on crossing over somewhere around 300Hz. The martin logan ESLs seem to cross over at 270Hz straight to the sealed bass. Know of any drivers that would be good for the low end? I suppose I'd need to do a lot of equalising and have a sturdy enclosure if I'm running it near 300Hz?

I'll be listening to these in a medium sized living room. So will get a good few meters of distance.

I was planning on having 1/16" gap each side from the diaphragm to the stators. I'll insulate the stators so I can really play around with the bias voltages to see what's good. As for the transformer, I read on another thread that you can use toroidal mains transformers? I have plenty of these. How will the iron core fare near the 300Hz point?
  Reply With Quote
Old 20th December 2010, 02:58 PM   #8
speedracer5 is offline speedracer5  United States
diyAudio Member
Join Date: Nov 2004
Location: Ohio
Sorry to be contrary but ESL's do not absolutely need to cross at such high frequencies. Listen to a 300Hz tone sometime. It is not bass by any stretch no matter how you slice it. ESL's can easily be run down to 80Hz with no excursion problems and probably lower. It is the lowest octaves that present a problem for a larger panel. By that I mean 6-8 inch wide and 45 inch tall effective area. Segmenting the panel is not necessary either. Even considerably conservative 100Hz is a better option. 300Hz is the lower midrange and it lies in a very critical and sensitive band of hearing. Many DIYers here cross their hybrid ESL's low instead of high (270-300) I am getting strong 40Hz bass out of a single Acoustat panel per side. Yes there are issues mostly with the lowest octave overdriving the panel. If I were to cut everything below 50Hz the Acoustats could do absolutely everything thrown at them with no problem. Also at 1/16" gap you may be better on efficiency but you really could afford to gap a bit bigger. 400 watts will do the job with a 1/8" gap depending on your charge voltage.

Last edited by speedracer5; 20th December 2010 at 03:01 PM.
  Reply With Quote
Old 20th December 2010, 03:04 PM   #9
speedracer5 is offline speedracer5  United States
diyAudio Member
Join Date: Nov 2004
Location: Ohio
Originally Posted by Ridin '24'z View Post
Know of any drivers that would be good for the low end? I suppose I'd need to do a lot of equalising and have a sturdy enclosure if I'm running it near 300Hz?
300Hz has got to be one of the nastiest resonances for dynamic woofers in a cabinet to deal with.
  Reply With Quote
Old 20th December 2010, 03:04 PM   #10
Ridin '24'z is offline Ridin '24'z  United Kingdom
diyAudio Member
Join Date: Aug 2006
I plan on using a digital EQ so I can play around with these things.

I'm tempted to even go even wider, about 1ft. Will I need to use a thicker insulation between stators and diaphragm?

The stator material I plan on using is 60deg Perforated galvanised steel with 3mm dia holes, 1.6mm thick, 51% open area. Sound reasonable? I can go with more open area, but I can only find ones with 6mm holes, is this a better choice or are the holes too big?.
  Reply With Quote


Open baffle vs ESL?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Does open baffle suffer from baffle step? 454Casull Multi-Way 15 19th May 2012 04:12 PM
Open-baffle baffle length matejS Multi-Way 2 21st September 2010 05:49 PM
Murphy baffle radios [ open baffle ] keithpeter Full Range 10 11th September 2007 08:59 PM
what effect does baffle have on open-baffle system? kappa546 Multi-Way 6 24th January 2006 11:21 PM
Australians- what solid timbers for baffle? (open baffle loudspeaker) tktran Multi-Way 13 30th November 2004 12:09 AM

New To Site? Need Help?

All times are GMT. The time now is 11:07 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio