Aleph 5, start up problem. - diyAudio
Go Back   Home > Forums > Amplifiers > Pass Labs

Pass Labs This forum is dedicated to Pass Labs discussion.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 5th December 2006, 08:58 PM   #1
diyAudio Member
 
Join Date: Oct 2004
Default Aleph 5, start up problem.

Hi, sorry to disturb you with this type of question but I couldn't find any answers that suits my questions in the old threads.

I have been struggeling with a start up problem some time now. At power on/off it takes about 1-2 seconds for the DC voltage at the output to be stabilized.
First I thought that the problem were caused by decoupling of the zener diode that sets the voltage to the current mirror in the input stage. Removing the decoupling took away some of the problem but not all, the start up time were about 10 seconds from the beginning.

http://www.kk-pcb.com/aleph-5.html

Looking at the feedback path in the schematic in the link above, the 100k resistor that is in series with the 220uF capacitor and 10k to ground, the time constant for this path is abround 1-2 seconds, could this be the problem?

As output devices I use one pair of FB180SA10. Could that be the problem?

http://www.alliedelec.com/Images/Pro...es_2737685.pdf

Since the turn on time is so slow, there is no "bump" in my speakers, the speaker cone is only slowly mowing, first back and then back to it its centerpoint.

What happens when you turn on your aleph, how long time does it take before they are stabillized? Is 1-2 seconds a problem for a speaker?


/Andy
  Reply With Quote
Old 5th December 2006, 11:25 PM   #2
The one and only
 
Nelson Pass's Avatar
 
Join Date: Mar 2001
If you use a coupling cap in the feedback network of this
circuit, it will hold a charge if there is offset when the amp
has just been turned off, particularly if there has not been
a load. When you turn the amp back on, the feedback will
swing the output to remove this charge. The bigger the
cap, the bigger the charge.

You can put some resistance, say 47K in parallel with the
cap to bleed it off, or you can wait longer between turn-off
and turn-on. Also, maybe you want to have a bleeder
resistor across the power supply, say 4.7K @ 3W per rail
to ground.

This presumes that the DC offset of the circuit is nominal
with the cap bypassed altogether. You should adjust the
current fed to the input diff pair to minimize this. Also, as you
note, putting a cap in parallel with the zener diode reference
for the input bias current source will allow for some thump.

  Reply With Quote
Old 6th December 2006, 12:05 AM   #3
RoboMan is offline RoboMan  Hong Kong
diyAudio Member
 
Join Date: Jul 2006
Further to Mr. Pass's suggestions, it may be a problem that the power supply takes too long to settle down.
  Reply With Quote
Old 6th December 2006, 10:08 PM   #4
diyAudio Member
 
Join Date: Oct 2004
Hi, thanks for the input.

Nelson Pass:

I measured the DC level before I started the amp today, 24 hours after I turned it of, and it measured 2.4V, the feedback capacitor needs to be discharged in other words.

I haven't tried your suggestions yet, want to make sure that I understand them correct first.

In the attached schematic I have added the R26=47k resistor to discharge the capacitor in the feedback path. My only concern is that the DC gain will be approximetly 2 and thereby an increased DC level at the output. You are mentioning that the bias current should be adjusted (i.e. R3 or change zener value of D1) but I don't see how the current adjustments could improve the DC level at the output (if I'm not using a potentiometer at the sources that could trim the currents individually in the diff pair, maybe that is what you mean).

What is the reason for adding bleeder resistors, except for discharging the power supply slowly?

RoboMan:

I'm using a CLC network in the power supply but I couldn't afford so big inductors and capacitors that it should be a problem, calculations and measurements also shows that there shouldn't be a problem.

Thanks again

/Andy
Attached Files
File Type: pdf aleph5update.pdf (28.1 KB, 184 views)
  Reply With Quote
Old 19th January 2009, 10:12 AM   #5
diyAudio Member
 
Join Date: Dec 2008
This is great stuff.

Many years ago I used a FB180SA10 MOSFET in the design of a DC motor speed controller.

A few weeks ago I stumbled apon Gamut ($$$) amplifiers
and they use a single MOSFET instead of matching up transistors.


I do have some questions concerning this amp design.

1) Is there a reason why the unbalanced Zin has been choosen to be so low ???

2) Have you tried using a matched pair of p channel JFET's for the differential pair ???

3) Is there a reason to go with a p channel MOSFET for the current source on the differental pair ?
Or would a low noise bi polar be fine for this application ???

Paul
.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Elektor soft start circuit problem supernet Solid State 15 23rd July 2010 11:11 PM
Punch 45 - Weird Problem with Start-up bigphil Car Audio 5 30th December 2008 08:59 AM
Irritating problem with soft start Rob11966 Tubes / Valves 23 24th November 2008 08:19 PM
Problem solved: DVD player cannot start all DVDs fiak Digital Source 4 14th November 2008 10:07 AM
Technics SP-10 MkI Start/Stop problem jgc31746 Analogue Source 2 13th April 2007 11:40 AM


New To Site? Need Help?

All times are GMT. The time now is 11:48 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2