New aleph 5 up and running, have a few ??'s about my measurements. - diyAudio
Go Back   Home > Forums > Amplifiers > Pass Labs

Pass Labs This forum is dedicated to Pass Labs discussion.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 21st December 2002, 04:41 PM   #1
RKC is offline RKC
diyAudio Member
 
Join Date: Dec 2002
Location: Dallas, TX
Default New aleph 5 up and running, have a few ??'s about my measurements.

Hello all, I've read/learned quite a lot over the last year on this site while building up my aleph 5 clone. I finally got a chance to turn on one channel yesterday and except for a small wiring oversight everything worked wonderfully. My DC offset was 13mv, and powersupply hum is about 75 mv with only 1/2 of my capacitor bank hooked up. The sound was fanatastic, as good as can be expected with one channel anyway. I made some measurements at all of the voltage test points in the aleph 5 schematics and most of them are fine. But a few are off a and I was going to see what you folks thoughts on these measurements are. I think most of my differences are due to running a higher rail voltage +/- 35.6V. The main differences I have from the sch voltages are the bias I'm seeing about .66v across the source resistors. I've read some other posts on this and I think I know what I need to do to correct this. But I'm seeing 5.2 V across r11 to Q3 and I'm seeing 3.55V on the source's for Q1/Q2 which according to the sch. should be 4V. Any thoughts on this, should I change the R11 value to change the voltage drop? Any input would be appreciated. Thx...
  Reply With Quote
Old 21st December 2002, 05:36 PM   #2
diyAudio Member
 
Join Date: Jan 2002
Location: Philadelphia
Your voltages all look fine. The only thing you should do is change the value of R19. Making it smaller will decrease the bias across the source resistors. You could solder a large (>500K) resistor in parallel with the 221K.
Or just replace it with something smaller around 200K is a good start. Keep decreasing it until you get the bias you want. Changing R11 will do nothing to change the voltage across it, you would only change the tail current which biases the differential input pair.
Hope this helps

Good Luck
Jake
__________________
audio4life
  Reply With Quote
Old 22nd December 2002, 11:32 AM   #3
Mad_K is offline Mad_K  Norway
diyAudio Member
 
Mad_K's Avatar
 
Join Date: Sep 2002
Location: Norway
-Don't change anything!

Your voltages are right on spec.!

The voltage points in the scematic are not that exact. For example, there SOULD BE 0,66V across the source resistors, and not 0,5V as stated. (Total bias now: 0,66*3=1,98A = Perfect !)
__________________
Mads K
  Reply With Quote
Old 23rd December 2002, 04:36 AM   #4
RKC is offline RKC
diyAudio Member
 
Join Date: Dec 2002
Location: Dallas, TX
Thx for the replies, After sitting down and figuring it up. It looks like I'm running about 4amps total across all 6 of the IRF240's for the one channel. Which figuring in my rail voltage puts me at about 140w of idle power. Which is pretty close to what the book and others have said is the normal power draw for one channel(150w).
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Another Aleph X up and running xavier1000 Pass Labs 94 17th March 2011 06:20 PM
What advantages running ported midbass if you are running a sub? mitchyz250f Multi-Way 3 20th May 2008 02:34 PM
Aleph-x running, but a little problem oliverniekamp Pass Labs 18 7th May 2006 06:18 PM
Aleph board voltage measurements SteveA Pass Labs 8 21st January 2006 05:30 AM
Aleph 5 Running (Pic) Jye Pass Labs 5 7th February 2005 07:13 AM


New To Site? Need Help?

All times are GMT. The time now is 10:35 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2