Threshold Stasis 2. - Page 4

docjoe · 8th July 2005, 09:28 PM

hi steenoe and jacco
now i've completed a first 12 hours run.
the temp is about 40 ° C. and bias set 0.75 amp on both channel; offset is 10 mv on one chanel and 60mv on the other...
have to trim those 47R and 33R resistors in the diff pair, as I changed these to BC550c.

yes you have to cross the speaker wires, unless you display the back of the amp in your setup.

steenoe · 8th July 2005, 09:38 PM

Thats a pretty sight, doc

I really do not get this right/left thing on the rear panel

Hmmm, I guess my old friend has to wait a bit, before his amp is getting fixed! I simply do not have the time at this point, to make a larger restoring

Doc, do you have a specific opinion about what is causing the oscilation?? Maybe the Tantal's as you mentioned, or the trimpots?? If I had something specific, I might give it a shot

Thanks in advance

Steen

BTW I measured 40 deg C on the healthy channel and 50 deg C on the other.

apassgear · 8th July 2005, 10:31 PM

Quote:

Originally posted by docjoe

yes you have to cross the speaker wires, unless you display the back of the amp in your setup.

Hey guys, your not serious, are you???

To read them correct you must end those comments with a

steenoe · 8th July 2005, 10:45 PM

Quote:

Hey guys, your not serious, are you???

As a matter of fact, this is actually correct

At first I did take several readings on the rear panel, and had to conclude the facts: they actually swapped right/left on the silkscreening

Well, the guy doing this could be somehow excused, I guess

Looking at the rearpanel from aft, would imply that the right channel is at the left and "vica verca"

Steen

docjoe · 9th July 2005, 08:35 AM

yes that' correct, but I presume that for maintenance point of vue, if you work on it, the PCB, are on the back as are the bias pots, its seems easier to .
anyway even if they crossed sides, the diode bargrap display is ok!

steenoe · 10th July 2005, 08:30 PM

Just to let you guy's know, I decided to deliver the amplifier back to the (unhappy

) owner at this point

It was quite a hard decision, but I simple do not have the time for a major workover at this point. Besides, it is way too hot in Denmark, to do big soldering jobs right now

Thanks a lot for your inputs, anyway

I will keep you posted if (probably when!)
I take it it on again

Steen

docjoe · 10th July 2005, 09:04 PM

What, you guys in Denmark dont have air conditioning?
well in Paris it is about 20°c now

Well I think I've finished my rebuilt, I hope it will last another 25 years...
I'll be pleased to hear about you...

steenoe · 10th July 2005, 09:14 PM

Quote:

well in Paris it is about 20°c now

I am sure we have like 30C now, I feel for a swim right now! Lucky enough
to have Denmarks nicest beach, 500 meters away

Well, the guy actually took the hole thing in a cool way. He would look for a ML! He has a pair of big Apogee clones, and they really demand some power. Those darn speakers, which are very well build indeed, are the size of a door

But the impedance is hopeless

Otherwise, I would have made an Aleph for him, of course

The chassis with heatsinks could house an Aleph 5

Steen

apassgear · 11th July 2005, 01:20 AM

When he gets those ML buy his Stasis

Nelson Pass · 11th July 2005, 04:24 AM

Assuming that he still wants to sell it.

9th July 2005, 08:35 AM	#35
docjoe diyAudio Member Join Date: Jun 2003 Location: Paris, France	yes that' correct, but I presume that for maintenance point of vue, if you work on it, the PCB, are on the back as are the bias pots, its seems easier to . anyway even if they crossed sides, the diode bargrap display is ok! __________________ docjoe.

10th July 2005, 09:04 PM	#37
docjoe diyAudio Member Join Date: Jun 2003 Location: Paris, France	What, you guys in Denmark dont have air conditioning? well in Paris it is about 20°c now Well I think I've finished my rebuilt, I hope it will last another 25 years... I'll be pleased to hear about you... __________________ docjoe.

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
threshold stasis 2	docjoe	Solid State	3	10th November 2012 01:05 PM
Another Threshold Stasis 2 rebuild	AMV8	Pass Labs	2	22nd December 2006 06:13 AM
Threshold Stasis 3, too	Roscor61	Pass Labs	3	20th May 2004 10:12 AM
Threshold Stasis S/300-2 optical a-ab	georgehifi	Solid State	3	30th September 2003 03:18 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

8th July 2005, 09:38 PM	#32
steenoe diyAudio Member Join Date: Mar 2004	Thats a pretty sight, doc I really do not get this right/left thing on the rear panel Hmmm, I guess my old friend has to wait a bit, before his amp is getting fixed! I simply do not have the time at this point, to make a larger restoring Doc, do you have a specific opinion about what is causing the oscilation?? Maybe the Tantal's as you mentioned, or the trimpots?? If I had something specific, I might give it a shot Thanks in advance Steen BTW I measured 40 deg C on the healthy channel and 50 deg C on the other.

10th July 2005, 08:30 PM	#36
steenoe diyAudio Member Join Date: Mar 2004	Just to let you guy's know, I decided to deliver the amplifier back to the (unhappy ) owner at this point It was quite a hard decision, but I simple do not have the time for a major workover at this point. Besides, it is way too hot in Denmark, to do big soldering jobs right now Thanks a lot for your inputs, anyway I will keep you posted if (probably when!) I take it it on again Steen

11th July 2005, 01:20 AM	#39
apassgear diyAudio Member Join Date: Nov 2002 Location: Viña del Mar, Torreon	When he gets those ML buy his Stasis

11th July 2005, 04:24 AM	#40
Nelson Pass The one and only Join Date: Mar 2001	Assuming that he still wants to sell it.