Yet another variation on cascoded balanced line stage - diyAudio
Go Back   Home > Forums > Amplifiers > Pass Labs

Pass Labs This forum is dedicated to Pass Labs discussion.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 24th July 2002, 07:13 PM   #1
jwb is offline jwb  United States
diyAudio Member
 
jwb's Avatar
 
Join Date: Mar 2002
Location: San Francisco, USA
Send a message via AIM to jwb
Default Yet another variation on cascoded balanced line stage

Thanks Nelson Pass for the original design of the Zen balanced line stage.

This variation includes a cascode transistor on the gain device, and a cascoded current source to keep the bias current steady. The supply is +60/-20V. I could probably go all the way down to +60/-10V, and I already have the trafo for that negative rail

The bias LEDs in this design are amber Panasonic models that helpfully drop 2V when you put 10mA through them. The BJTs are Zetex E-Line packages that are compact and can dissipate useful power without heatsinks.

Q3 and Q4 are biased to 14V on the base. They hold the drain on Q1 and Q2 at 13V. I chose these bias levels to allow the output to swing down to +16V, given a 2Vrms input and a gain of 10 (20dB).

Q5/6 and Q7/8 form a steady 40mA current source, with the collector of Q7/8 held at -9.2V.

I'm a little skeptical of the role of Q3/4 in this circuit. By pegging Vd on Q1/2, it really changes the nature of the circuit. So, I am building the board with a socket for Q3/4. I will compare the sound with Q3/4 installed or jumpered.

Your thoughts and brutal flames are welcome.

Click the image to open in full size.
  Reply With Quote
Old 24th July 2002, 08:49 PM   #2
The one and only
 
Nelson Pass's Avatar
 
Join Date: Mar 2001
Very cool.

  Reply With Quote
Old 27th July 2002, 09:49 PM   #3
jwb is offline jwb  United States
diyAudio Member
 
jwb's Avatar
 
Join Date: Mar 2002
Location: San Francisco, USA
Send a message via AIM to jwb
Default Thanks Nelson

Here is the final schematic. Please ignore the +/-24V supply markings: those are magic symbols in Eagle and I can't change their value easily. The real supplies are still +60V/-20V.

Click the image to open in full size.

And here is the PCB layout I drew for it:

Click the image to open in full size.

The bigger version of the PCB layout is here:

http://atari.saturn5.com/~jwb/layout.png

The board is 3.9"x3.2" with two layers. I had a problem because the Hovland MusiCap 7uF output coupling capacitors are massive: 3.25"x1". These would have occupied the entire board, so I moved them off to the sides, and their lead wires solder into the pads marked OUTCAP.

I should be getting these boards within a week. Praise be to $33/each PCB houses.
  Reply With Quote
Old 31st August 2002, 07:17 PM   #4
jwb is offline jwb  United States
diyAudio Member
 
jwb's Avatar
 
Join Date: Mar 2002
Location: San Francisco, USA
Send a message via AIM to jwb
Default Final design changes

This design turned out to be unsatisfactory. After I built up both channels (but not on the breadboard), I measured a high amplitude 50MHz oscillation in the circuit. This was solved by inserting a 221Ω resistor between the base of Q5 and the top of the LED stack. For symmetry, I also made this change at the base of Q6. Q5 and Q6 are used to cascode and thereby improve the PSRR of the active current source. The insertion of the resistors should not impact this function, nor the sound of the circuit. Of course, by preventing oscillation, these two resistors will keep me out of trouble with the FCC

I also found the heatsink prescribed by Mr. Pass in "Balanced Zen Line Stage" for Q101 and Q102 insufficient. The heatsink -- Digi-Key part HS104-1 -- has thermal resistivity of 15.6°C/W. The TO-220 case of the IRF610 has thermal resistivity of 4.0°C/W from junction to sink. The IRF9610 is worse at 6.9°C/W. With my active current sources, I am drawing 200mA at idle, over a potential of 20V drain-to-source at Q101. This transistor needs to dissipate 4W. With this heatsink at standard temperature, the Tj will rise to 103°C. I found this to be slightly optimistic, since the temperature inside the chassis rises above standard temperature, and the IRF610 is rated to operate up to 150°C.

My solution was to use Digi-Key part HS104-2 with a thermal resistivity of 6.4°C/W, giving a nominal Tj of 67°C.

I also was not happy with the first revision of my circuit board. I made a second revision where the current flows straight across the board, and the signal lines don't cross or run parallel to the power. The modification for Q5 and Q6 is wired in point-to-point.

Click the image to open in full size.
  Reply With Quote
Old 31st August 2002, 11:06 PM   #5
diyAudio Member
 
Join Date: Jan 2001
Location: Scandinavia
Cascoded current sources are cool, but may I suggest that you consider putting some more diodes to drop more voltage across the emitter sense as I would think "agility" of the current source was more a function of emitter resistor drop than having a high Vce

Petter
  Reply With Quote
Old 31st August 2002, 11:44 PM   #6
jwb is offline jwb  United States
diyAudio Member
 
jwb's Avatar
 
Join Date: Mar 2002
Location: San Francisco, USA
Send a message via AIM to jwb
My intention was not to have a high Vce, but rather a stable Vce. The cascode holds Vc at 9.45V, Vb is 2V, and Ve is 1.45V. Current variation from Early effect should be nil, and I think 1.45V is enough across the emitter resistor to ensure that variations in Vbe are small by comparison.

What Ve would you recommend, and what effect would you expect? I could certainly see, for example, setting Vb to 6V for a 5.45V Ve and using a 110Ω 1% emitter resistor. But, I am indifferent about the effect this would have on the sound. I really don't care that much if the bias current drifts by a few mA over the course of an hour.
  Reply With Quote
Old 1st September 2002, 12:57 PM   #7
diyAudio Member
 
Circlotron's Avatar
 
Join Date: Jun 2002
Location: Melbourne, Australia
Is it really a good idea to cascode a fet and a bipolar? With a bipolar the drain current varies as the log of Vbe so when you cascode two bipolars you get a log / antilog function which comes out linear, but with a fet the drain current goes up as the square of Vgs. What square / antilog comes out to be is different to say the least. But in this balanced cct it may not matter because the nonlinearity cancels? I wonder how it would go with cascoded fets.

Also, is it really a good idea to have independent current sources down the bottom? A single one connected to *both* sources will definitely make the circuit balanced because it forces the total current to always be the same. When one side backs off the other side is made to turn on by an equal amount.

What is the reason for the cascode current source setup? I have never seen this before. Does it work over a wider range of voltages or have greater current constancy or something?

Congratulations on trying something new

GP.
  Reply With Quote
Old 1st September 2002, 04:41 PM   #8
diyAudio Member
 
jan.didden's Avatar
 
Join Date: May 2002
Location: Great City of Turnhout, Belgium
Blog Entries: 7
Default cascode stage

Hi jwb,

Great circuit, I like the elegant use of the cascodes. I also liked the first pcb layout wrt the star grounding for the supply caps. In fact, I would have connected R16 & 17 directly to the caps as you did with R11 & 12.
To cut down on cross-pcb signal lines you could relocate the resistors for the outcap+ terminals to the right close to the supply caps.

I noted that in the second version you went away from that. In fact, the gnd for the V+ now is shared among several stages, which brings the danger of mutual influence with oscillations and/or higher distortion. That first layout was really, really good, in my view.

Cheers, Jan Didden
  Reply With Quote
Old 27th October 2002, 05:19 PM   #9
jwb is offline jwb  United States
diyAudio Member
 
jwb's Avatar
 
Join Date: Mar 2002
Location: San Francisco, USA
Send a message via AIM to jwb
Thanks for the nice comments Jan. Did I ever mention how much fun I had building this preamp? Sounds great, if only I could make a nice chassis for it.

Here's one channel:

Click the image to open in full size.
  Reply With Quote
Old 27th October 2002, 05:20 PM   #10
jwb is offline jwb  United States
diyAudio Member
 
jwb's Avatar
 
Join Date: Mar 2002
Location: San Francisco, USA
Send a message via AIM to jwb
Plan view of same:

Click the image to open in full size.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Balanced Line Stage tonistefanovski Pass Labs 1 27th December 2005 09:25 AM
Balanced Zen v5 + balanced Zen line stage Adrie Pass Labs 0 30th May 2004 05:27 PM
Balanced Zen Line Stage Mad_K Pass Labs 55 30th December 2003 08:03 PM
Zen Balanced Line Stage Balanced vs Unbalanced macka Pass Labs 28 11th December 2002 06:18 AM
Balanced line stage lykkedk Pass Labs 1 5th December 2002 07:36 PM


New To Site? Need Help?

All times are GMT. The time now is 02:39 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2