ZEN/SOZ hybrid - diyAudio
Go Back   Home > Forums > Amplifiers > Pass Labs

Pass Labs This forum is dedicated to Pass Labs discussion.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 9th July 2001, 08:02 AM   #1
diyAudio Member
 
Join Date: Apr 2001
Location: Brisbane Australia
I've been thinking about the Pass DIY amp designs a lot lately and reading old threads about peoples efforts to taylor one of Nelson's designs to suit their personal tastes/needs. I was very curious to try the SOZ but didn't for 2 reasons

1)like so many others I could not justify the gross inefficiencies of the design.

2)No matter how hard I tried I could not get my head around how the circuit works (ie. how it can be scallable without changing resistor values) - Ohms law certainly doesn't explain things. As I believe everything I do should be a learning experience, building someone elses design without understanding how it worked did not appeal.

This is what I did:

I basically used 2 ZEN amplifiers per channel in a differential pair arrangement (as in the SOZ design). The amp uses a single positive supply rail (24V in this case). The gates are biased at 4 volts via voltage dividers directly from the supply (ie. no feedback). Because the inputs are above ground potential coupling capacitors are required as in the ZEN design. The mosfets are biased at 1.5A each through an 8 Ohm resistor per side giving 12V at the drain of each mosfet. This equates to 4W RMS per channel with an idling current of more than 4 times the maximum required by the load (8 Ohm).

I've only just finished this amp so I'll reserve my judgement on how it sounds (compared to the ZEN which I built) for a few weeks.

I would appreciate input from anyone who has an opinion on any of this especially the following.

1) Resistors Vs. Current sources
2) Benefits of operating at higher idling currents/employing deeper suppliy rails (I posted this question a little while ago but nobody was interested, figure I'll try it again)
3) There was mention in a therad some time ago (I think it was grey) of the possibility of doing away with the input coupling cap. Something about the preamp of a tube amp. Cananyone eleaborate on the possibilities of removing this capacitior while keeping a positive bias at the gate.

Cheers

Dan
  Reply With Quote
Old 9th July 2001, 07:13 PM   #2
diyAudio Member
 
Join Date: Feb 2001
Location: Columbia, SC
Dan,
I'm short on time, but you've tapped into a topic that is of current interest to me. (Okay, okay...along with about 20 others.)
1) I think the idea of differential Zen amps should be followed up. Note that if you can get the circuit running properly (shouldn't be hard), you should be able to remove the output coupling caps, as the DC from one amp should come pretty close to balancing the DC from the other. Yes, you'd need to float the output from ground or run one or both sides to ground through a resistor--but you'll end up floating the output anyway, yes?
2) Once I get the second pair of Aleph 2s up and running, I have several experiments in mind. One is to run Alephs as a differential pair as an intermediate step towards an X/Aleph hybrid circuit. Since the Aleph and the Zen circuits are cousins, you and I may be able to compare notes.
More later, hopefully, as I've been cogitating on this for a while...

Grey
  Reply With Quote
Old 9th July 2001, 09:28 PM   #3
diyAudio Member
 
Join Date: Apr 2001
Location: Brisbane Australia
Grey,

The amp is operational and I never included the DC blocking caps on the outputs as the DC offset is very low (I verified this before hooking up to my good speakers). I haven't referenced the outputs to ground through 100 Ohm resistors as in the ZEN schematic. I didn't feel they were necessary as I have not seen any differential style amp stages using them. Is there a reason I should be using these?

I probably should note that I am driving the amp from an unbalanced input. This is not how I want to use this amp so I will be building something similar to the BOSOZ when time/money permits.

Dan
  Reply With Quote
Old 9th July 2001, 11:08 PM   #4
grataku is offline grataku  United States
diyAudio Member
 
Join Date: Dec 2000
Location: -
How about we agree on a name for this new design: the BOZO.
  Reply With Quote
Old 9th July 2001, 11:48 PM   #5
diyAudio Member
 
Join Date: Apr 2001
Location: Brisbane Australia
I believe Grey coined this style of amp (in another thread) as the illegitimate son of zen so I guess we will call this and other such incarnations ISOZ

Dan
  Reply With Quote
Old 10th July 2001, 12:47 AM   #6
diyAudio Member
 
Join Date: Feb 2001
Location: Columbia, SC
Dan,
I've been trying to sneak a few minutes to post for the last couple of hours. Let's see how far I can get.
1) I'm on record as preferring resistors to current sources sonically. However, there are times when a current source is the best solution to the problem. I used one to drive the input differential to my tube amp, as it gives near perfect results when used as a phase splitter--something you could consider for conversion of unbalanced signals to balanced. Others will disagree (what? you're surprised?). Jam feels that current sources (and their sundry variations) can be tamed. My rejoinder is that lions can be tamed, too, but that doesn't mean that I want one as a pet...
2) All things being equal (as remote a chance as getting fat women to quit wearing spandex), higher current is a Good Thing. Rails can then be expanded up to the point where the device is up against thermal limits. How hard you want to push your gain devices is up to you.
3) There are two pretty good options for getting rid of those pesky input caps: First, go to a bipolar power supply for the Zen (but by the time you do this, you're within spitting distance of building an Aleph, might as well go whole hog); second, go to a depletion mode gain device. Okay...what's a depletion mode device? A depletion mode device is a tube or JFET; a device whose grid/gate is more negative (for JFETs we're assuming N-channel, which is the most common sort of JFET, anyway; tubes are sorta N-channel by default) than the cathode/source. Depletion mode devices are self-biasing, which means that you can tie the cathode/source to ground with a resistor (or current source) and ground the input (yippee! no cap!). The quiescent current flows through the resistor, giving you a positive voltage offset for the cathode/source, leaving the grid/gate negative by comparison.
If I understood your description of your circuit, you don't need to ground reference your output. It's just an option.
Running an unbalanced input into a balanced circuit requires a phase splitter (even if it's just handled by the circuit itself). If you've got one Zen input grounded and are putting the signal into the other input, you're probably not getting very symmetrical drive right now, so the circuit may now be functioning at its full potential yet.
This is probably pretty disjointed, as I keep getting interrupted by the real world (boring stuff like earning a paycheck). Ask questions as necessary.
Back to you.

Grey
  Reply With Quote
Old 10th July 2001, 03:00 AM   #7
diyAudio Member
 
Join Date: Apr 2001
Location: Brisbane Australia
Grey,

Although I have no reason to prefer resistors (ie. I've not had enough time playing with these things and listening to the results to have a valid opinion about whats better) I prefer to use them instead of constant current sources due to the simplicity of the circuit. I like things as simple as possible, I think at this stage of my hobby I require said simplicity so I can see the woods without the trees clouding my vision.

Although I am using relatively high current in this circuit, due to the low power (4W/ch) the devices are well within their temperature limits. This reminds me of a question I had; If both legs of a differential amplifier are biased at say 1.5A, does the load see 3A?

Funny you should mention JFETS as I have been doing a little research into using these devices myself. Once again I refuse to construct a circuit I do not atleast partially understand so the use of these devices in this style of circuit will have to wait until I have the time to research it fully.

One thing about JFETS, how does their much lower transconductance affect their use in a circuit such as the one we are discussing? What mods have to be made?

You mentioned in a previous post using split-unequal rails to bias the SOZ circuit to increase the efficiency. I was thinking of removing the bottom 8 Ohm resistors from the SOZ circuit and with a unequal supply (eg. +20V & -5V) bias the mosfet through the 8 Ohm resistors up top and the 1 Ohm resistors down below. What are your thoughts?

Your right I am grounding one of the inputs which I understand creates an increase in distortion from balanced inputs, but at this stage I don't see what other option I have. Any ideas?

Dan

  Reply With Quote
Old 10th July 2001, 03:26 AM   #8
jam is offline jam  United States
diyAudio Member
 
jam's Avatar
 
Join Date: May 2001
Location: Auburn, CA, USA
Dan,

Is it possible to post your schematic or e-mail it to us. It sounds interesting.

Despite Grey's and my differences on current sources there are probably advantages to both approaches. Experiment and choose the one that sounds the best. I had suggested to Grey to try an experiment and replace the current source of an Aleph differential with a resistor attached to a higher B+ rail which is an experiment I should try it but alas I don't have Alephs anymore, but I am open to the possibility that this might be a viable solution.

After all if we don't explore different solutions to problems we don't advance our knowledge.

Jam

P.S. Depletion mode N-channel mosfets are available but they are rare and I have not been able to locate any power or P-channel devices.

  Reply With Quote
Old 10th July 2001, 03:29 AM   #9
diyAudio Member
 
Join Date: Apr 2001
Location: Brisbane Australia
Default How do you do that

I have seen schematics posted on the forum before (sometimes it works sometimes it doesn't) how do I put a picture in my post?

Dan
  Reply With Quote
Old 13th July 2001, 09:43 PM   #10
diyAudio Member
 
Join Date: Apr 2001
Location: Brisbane Australia
I've been listening to this amp for a while now and I think I can give some observations/listening impressions. I will not make outright statements rather comparisons to the ZEN amp which I already built.

The music is detailed, maybe a little more than the ZEN. The music seems very forward almost to the point of being too bright on some tracks. The warmth of the reproduction (artificial or otherwise) of the ZEN which I so like is not absent but a little less with this amp.

I am still not sure which I prefer and for reasons stated below I will not make a judgement just yet.

There are a few things which I should point out which may have produced the characteristics I am describing.

1) In my ZEN I bypassed both the input and output coupling caps with metalised film polyprops. Although the output coupling caps aren't required I still use a 47uF electrolytic on the input which at this point is not bypassed. I will be doing this today and reporting any differences I hear.

2) As stated in a previous post I am still using the feedback circuit from the ZEN. This is another modification I hope to make this weekend.

3) I am using an unbalanced input and grounding the other input.

Could any of the above give rise to the differences in sound I have discerned. Is what I discribed above what a SOZ is supposed to sound like?

Dan
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Hybrid Car Amp... let's try jeppix Car Audio 19 18th August 2008 05:48 PM
the hybrid one arhi45 Tubes / Valves 11 8th May 2007 08:44 PM
Hybrid Ply / MDF ? Renron Multi-Way 5 8th February 2007 10:49 PM
My wacky idea for a hybrid horn loaded woofer/planar widerange hybrid loudspeaker. Spasticteapot Multi-Way 0 30th November 2006 04:16 AM


New To Site? Need Help?

All times are GMT. The time now is 08:05 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2