Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Pass Labs This forum is dedicated to Pass Labs discussion.

Help me with this toroid!
Help me with this toroid!
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 10th August 2017, 09:03 PM   #21
Nelson Pass is offline Nelson Pass  United States
The one and only
 
Nelson Pass's Avatar
 
Join Date: Mar 2001
Help me with this toroid!
If they were out of phase, you would really know it.

  Reply With Quote
Old 10th August 2017, 09:11 PM   #22
Hikari1 is offline Hikari1  United States
diyAudio Member
 
Join Date: Jun 2012
Location: Seattle
Ah, I understand. Pretty sure they were out of phase in the "R&D" phase of this project.
Light bulb limiter came in handy.

F5T is up and running now w/32V rails (30.9 loaded) and dual pairs of Toshiba Mosfets. Bias is 1.8A per channel.

I think I liked it better at 24V rails and 2.4A bias. But the headroom is nice.

Bias is certainly king if you don't need the power.
  Reply With Quote
Old 11th August 2017, 12:02 AM   #23
CanAm Man is offline CanAm Man  United States
diyAudio Member
 
Join Date: Sep 2006
Location: Santa Rosa Beach, FL
If they were out of phase, then either you would have:

1. Effectively be a "bucking transformer", with zero volts appearing on the secondary windings--if only for an instant of time...(!)

2. You would have created a cold fusion thermo-cryogenic reactor.

Only kidding--with the voltages you have on your current (no pun intended) secondaries, you are OK--you have the primaries "in phase"..... As an aside, if you even wanted/needed/desired a higher rail voltage, you could use the 100v primaries, rather than the 120v primaries, to get a rail voltage that was about 20% higher. (However, noo need to try this for your amp...)
  Reply With Quote
Old 11th August 2017, 08:03 AM   #24
AndrewT is offline AndrewT  Scotland
diyAudio Member
 
Join Date: Jul 2004
Location: Scottish Borders
Using a 110Vac, or 120Vac supply into a 100Vac rated primary is likely to saturate the transformer (especially any of the continuous lamination cores) and lead to severe overheating.

It is OK to go the other way: use a lower supply voltage into the higher rated primary. The only downside is a reduction in the effective VA.

The manufacturers provide tappings to avoid those problems.
A multi-tapped primary usually has windings in 5Vac increments.
100, 105, 110, 115, 120 would be typical for a transformer that can be used on any supply voltage from 97.5Vac to 122.5Vac
And with the correct tapping selected the transformer will be within 2.5Vac of it's rating.
This minimises the risk of saturation and maximises the available VA.

If it was a dual primary, then it now covers the range from 197.5Vac to 242.5Vac in 5Vac increments.
__________________
regards Andrew T.

Last edited by AndrewT; 11th August 2017 at 08:08 AM.
  Reply With Quote
Old 12th August 2017, 10:16 PM   #25
CanAm Man is offline CanAm Man  United States
diyAudio Member
 
Join Date: Sep 2006
Location: Santa Rosa Beach, FL
Good point, Andrew..... Either use (as a bucking transformer to reduce output voltage, or using a lower-voltage primary to step up the output voltage) aren't sound engineering techniques..... I've used them before--but only on breadboards and for prototyping--when I didn't have the appropriate transformer on the shelf.

Neither are an "optimal approach" for a best-practice design.
  Reply With Quote

Reply


Help me with this toroid!Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
winding a torroid ?? Minion Power Supplies 7 22nd October 2011 10:58 PM
need help picking torroid oiphy Power Supplies 2 13th September 2011 05:11 AM
Q on torroid mounting weinstro Power Supplies 3 25th January 2006 12:22 AM
small crack in torroid!!future of torroid? sagarverma Power Supplies 24 8th November 2005 04:22 PM
Torroid vs. SMPS ChocoHolic Power Supplies 55 21st August 2005 01:34 AM


New To Site? Need Help?

All times are GMT. The time now is 01:52 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio
Wiki