F3 mono blocks - diyAudio
Go Back   Home > Forums > Amplifiers > Pass Labs

Pass Labs This forum is dedicated to Pass Labs discussion.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 30th December 2012, 12:47 AM   #1
yup is offline yup
diyAudio Member
 
Join Date: Oct 2002
Location: Atlanta, GA
Default F3 mono blocks

Hi everyone,
I have finally powered up my pair of mono block F3's that I started several years ago (good thing I don't do this for a living). Between life and all the time I have been sitting and listening to my Aleph-X, I have yet to finish this pair of amps.... until now.
These amps started out originally as ZV9's, but I converted them over to F3's as I completed assembly. The main heat sinks were surplus that I picked up a while ago. The basic construction of these amps was simple due to the machine equipment that I have readily available. These will be placed directly behind my main speakers since the best speaker cable is none at all, so appearance is not a major concern (but they do need to look presentable since they will be in the living room).
Now that I have both amps up and running, I have a few questions about adjusting them. I have attached a copy of the F3 schematic with the voltages that I am currently measuring ( both amps are basically the same) after an hour or so of warm up time.
The first thing that stands out is that I only have about 1.7 volts across Q1 (not the 2.5V for optimum load line cancellation). Based on the voltages across R6, 7, 8 it looks like I am only biased to about 1.3 amps. This is confirmed by the maximum heat sink temp of 110F near Q2 & Q3. Being mono blocks, I probably have more than enough heat sink capability (don't hear that too often...)
My first thought is to increase the bias current by reducing R8 to 1ohm (possibly lower?). I think I should be aiming for 2 amps bias current minimum based on the ZV9 literature. If this is correct, should I continue to increase the bias current beyond the 2 amp setting if the heat sinks will allow it (and I don't reach the limit of the Jfet)? At some bias level will the load line cancellation effect be reduced (assuming I maintain 2.5V across the Jfet - by adjusting R3,4,5)? Unfortunately I do not have access to a trustworthy distortion analyzer...

Both amps are behaving identically and I don't see anything funny on the scope or hear anything odd on my shop speakers. The maximum gain I am able to achieve is about 11.6db by adjusting P2. Nelson lists 12.75db as the gain for the FW F3.

Thanks

Click the image to open in full size.
Click the image to open in full size.
Click the image to open in full size.
Click the image to open in full size.
Click the image to open in full size.
Click the image to open in full size.
  Reply With Quote
Old 30th December 2012, 12:50 PM   #2
generg is offline generg  Germany
diyAudio Member
 
generg's Avatar
 
Join Date: Jul 2009
Location: Near Frankfurt
You are very close....

"I recommend that you simply select R3 so that the Vds of the JFET in the amplifier is 2.5 voltswith the output DC figure of 23 volts. More often than not, this is close to the
sweet spot."
Nelson in the ZV9 article, do it by playing with R5.

But first try to get 23 V at the output node as Nelson mentions.... with P1. May be the other values will come in the ballpark .....Maybe you have to change R13 a bit.
__________________
and the First Wtt is......a really First Class PSS Idea

Last edited by generg; 30th December 2012 at 12:52 PM.
  Reply With Quote
Old 30th December 2012, 01:27 PM   #3
yup is offline yup
diyAudio Member
 
Join Date: Oct 2002
Location: Atlanta, GA
Default still confused

I still have enough adjustment left in P1 to adjust the DC voltage at the output cap up or down. Currently I have it at approximately 21V based on the F3 schematic I have posted - 1/2 of the 42V regulated supply voltage.

I have read the ZV9 and F3 papers so many times I can't count them all. Many thanks to Nelson for the education. I seem to recall that there was an F3 "service manual" (not the product manual), but I cant find it lately so I am guessing my mind is playing tricks on me...

My supply voltages are almost exactly the same as the F3 schematic (the ZV9 is slightly higher).

Right now each mono block is dissipating about 58 watts at idle (not the 100 watts/channel mentioned in the F3 user manual).

This low dissipation, the reduced voltage across the Jfets, the upper limit of the gain (P2 set to limit), and the noticeably cool (compared to Aleph-x) heat sinks all lead me to believe that my bias current is too low.

A couple of differences between the two versions are R8 (ZV9=1ohm; F3=2ohm - a total of 0.33 ohm vs 0.40 ohm), and R14 (ZV9=1.0k; F3=1.5k)

The Vgs of my Jfets are 1.03, so I have R5 (R3 on the ZV9 schematic) set at 1.5 ohms per the ZV9 article.
  Reply With Quote
Old 30th December 2012, 01:51 PM   #4
generg is offline generg  Germany
diyAudio Member
 
generg's Avatar
 
Join Date: Jul 2009
Location: Near Frankfurt
You convinced me that you have read the article.....and I was a bit incorrect ...

Hm, hm .... You cannot measure the distortion, I suppose. Would make things clearer.

So it is difficult to say if it is more important to have the voltages shown in the circuit. They that may be correct only for a certain LU, or to follow the way with the diagram and choose the R5 according to the Vgs.

The original F3 I had for some time had k2 about 6db above k3 and it was possible to reduce still the distortion by adjusting P2. But I like a bit higher K2.

And my F3 clone ALSO had less gain like yours and I do not know why...

But there is an order of recommendations not having the possibility to measure distortion.

The better is the diagram using the Vgs to determine R5 .....and the worse to adjust for 2,5V Vds.
Why don't you change R6/7/8 in the direction of ZV9 to have at least 1,5A.

Finally I think your F3 will sound already good! And it looks really fine!
__________________
and the First Wtt is......a really First Class PSS Idea

Last edited by generg; 30th December 2012 at 01:55 PM.
  Reply With Quote
Old 30th December 2012, 01:59 PM   #5
generg is offline generg  Germany
diyAudio Member
 
generg's Avatar
 
Join Date: Jul 2009
Location: Near Frankfurt
For the aleph current source I finally decided to use Nelson's old ZV rule, 70% of the AC voltage you find over the 0R47 should be over R6/7/8.

I hope I am correct... I found it in ZV2 I believe....
__________________
and the First Wtt is......a really First Class PSS Idea

Last edited by generg; 30th December 2012 at 02:15 PM.
  Reply With Quote
Old 30th December 2012, 02:13 PM   #6
generg is offline generg  Germany
diyAudio Member
 
generg's Avatar
 
Join Date: Jul 2009
Location: Near Frankfurt
and last thing...

the diagram values may be optimized for the 23V of ZV9 and not for the 21V of F3.......
__________________
and the First Wtt is......a really First Class PSS Idea
  Reply With Quote
Old 30th December 2012, 02:26 PM   #7
yup is offline yup
diyAudio Member
 
Join Date: Oct 2002
Location: Atlanta, GA
Default More measurements, after running all night...

I have rechecked the voltage across R6/7/8 since my earlier measurements looked a little bit off (taken over a short time period, so voltage probably drifted slightly).

The voltage across R6/7/8 is 0.654Vdc, more in line with the 0.66 that it is supposed to be.

This puts my idle dissipation at 75 watts per mono block (including regulation). This makes me wonder if Nelson reduced the dissipation of the F3 from the ZV9 due to the thermal limit of his chassis, or to reduce distortion, or I am totally confused

Either way, the voltages across the Jfet still look odd (Drain 2.526v, Source 0.979v) - the Jfet is dissipating 2.55 watts - 1.55 volts/1.65A (much lower than the 4 to 6 watts in the ZV9 article)

My current understanding is that the voltage across the jfet is the most important to bring the device into the linear operating range, beyond that, the higher the bias current the better (depending upon heat sink capability)

I have enough heat sink capacity to increase the idle current beyond 2 amps.
  Reply With Quote
Old 30th December 2012, 02:39 PM   #8
generg is offline generg  Germany
diyAudio Member
 
generg's Avatar
 
Join Date: Jul 2009
Location: Near Frankfurt
"This makes me wonder if Nelson reduced the dissipation of the F3 from the ZV9 due to the thermal limit of his chassis"

yes I think so! and using the normal First Watt PSU....!

you are in the linear region I suppose....!

and sweet spot..... matter of interpretation.... lowest distortion at 1 Watt, or k2 over k3 at 1 Watt, but how much? Or better the k2 dominant at the Watt level you are hearing your music as Nelson once suggested?

I would say you can go for the values of ZV9. The scheme was published after F3 so I think Nelson optimized it even against the F3 .....that´s his character....
__________________
and the First Wtt is......a really First Class PSS Idea
  Reply With Quote
Old 30th December 2012, 02:48 PM   #9
yup is offline yup
diyAudio Member
 
Join Date: Oct 2002
Location: Atlanta, GA
Quote:
Originally Posted by generg View Post
and last thing...

the diagram values may be optimized for the 23V of ZV9 and not for the 21V of F3.......
Generg,
This is the reason for my confusion. The voltages/values in the First Watt F3 schematic above are different that the voltages listed in the ZV9 schematic.

The voltage across the Jfet is actually higher on the F3 (F3=2.4v; ZV9=2.0v) even though the supply voltage is slightly lower. In both cases the power dissipated is 4 watts.

On my amps the voltage across the jfets is 1.547v at 1.65A, or just 2.55W
  Reply With Quote
Old 30th December 2012, 02:50 PM   #10
generg is offline generg  Germany
diyAudio Member
 
generg's Avatar
 
Join Date: Jul 2009
Location: Near Frankfurt
the same with me I did not care.....

but may be Zen Mod, who made many work on the F3 will assist us....

__________________
and the First Wtt is......a really First Class PSS Idea
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Dartzeel mono blocks. Bonsai Everything Else 25 6th November 2012 11:31 PM
now mono blocks! ksporry Tubes / Valves 0 5th February 2011 07:32 AM
Grounding When Doing Mono Blocks jawbreak Chip Amps 5 5th September 2007 08:46 PM
100watt mono blocks yise1 Tubes / Valves 2 27th August 2006 05:29 AM
Bridging Mono Blocks jwatts Tubes / Valves 8 12th February 2005 07:23 PM


New To Site? Need Help?

All times are GMT. The time now is 01:21 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2