YAA! (Yet Another Aleph) Complete - Page 3 - diyAudio
Go Back   Home > Forums > Amplifiers > Pass Labs

Pass Labs This forum is dedicated to Pass Labs discussion.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 6th November 2003, 07:37 PM   #21
diyAudio Member
 
Sandy H.'s Avatar
 
Join Date: Nov 2002
Location: Charlotte, NC - USA
Da5id4Vz,

No kidding, I heard that rubbing a white ring stain in shellac hard with mayonnaise and a cloth will help evaporate the stain out. Is the mayo critical? I don't know, never had to try it.

Check google for shellac and mayonnaise. I'm surprised that more than one result recommends this method.

Sandy.
  Reply With Quote
Old 6th November 2003, 07:42 PM   #22
diyAudio Member
 
Da5id4Vz's Avatar
 
Join Date: Feb 2003
Location: lost in america...
Send a message via AIM to Da5id4Vz
Thanks for the tip; it may have helped with the cheeseburger too. My wife used some patented miracle product on it and it looks almost perfect, except for maybe missing a few layers of shellac.

The mayo likely would have been a better solution.
  Reply With Quote
Old 19th November 2003, 01:27 PM   #23
diyAudio Member
 
ace3000_1's Avatar
 
Join Date: Mar 2003
Location: spain
Send a message via Yahoo to ace3000_1
Default relder

heya relder, nice job on the amp, a very nice job! if u dont mind me asking whats the power output of the amp?

Thanks
Trev
  Reply With Quote
Old 19th November 2003, 03:36 PM   #24
diyAudio Member
 
relder's Avatar
 
Join Date: Jan 2002
Location: Tucson, AZ
Blog Entries: 14
Send a message via Yahoo to relder
Default Re: relder

Quote:
Originally posted by ace3000_1
heya relder, nice job on the amp, a very nice job! if u dont mind me asking whats the power output of the amp?

Thanks
Trev

Thanks, 47W into 8ohm.

Which leads me to a question. I measured RMS voltage at 1KHz just before visible clipping on the scope is apparent. Is this the usual way or is the point just before clipping not the standard metric? Since it seems most specs also quote a THD at rated power, the power, it would seem, is toned down until a desirable THD spec is found and then the voltage is taken?

Rob
  Reply With Quote
Old 19th November 2003, 11:10 PM   #25
Mark Kravchenko --- www.kravchenko-audio.com
diyAudio Member
 
mwmkravchenko's Avatar
 
Join Date: Jan 2002
Location: Perth Canada
Default Verrrrr Veeerrrrrr NICE

Great job and one to emulate if possible.

Dude with ring on his table. Get youself a damp(not dripping but wrung out) cloth and an iron. Put the damp cloth on the ring and palce your hot iron on the cloth. Warm it up and check often. The white rings are water that is trapped under the finish. The damp heat will release it. Btw french polish looks nice but it has pitfull wear characteristics. Not reccomended for a high wear surface.

Keep up the good work and hope this helps.

Mark
__________________
Mark
  Reply With Quote
Old 24th November 2003, 01:14 AM   #26
Blues is offline Blues  United States
Lightning In A Bottle
diyAudio Member
 
Blues's Avatar
 
Join Date: Sep 2003
Location: The Milky Way
Beautiful piece, Tuco ...I mean relder! I am sure you are enjoying every minute with your ears and eyes. I 'm also trying my hand on wood. I've settled with rubbed-on Teak/Golden Oak oil. French polish will be nice too, if I'll learn and have patience to do it. I've read people rubbing in 10 coats of shellac for max protection.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
WTB: Aleph Amp complete Fishfood Swap Meet 30 2nd June 2006 04:02 PM
FS: Complete Aleph P 1.7 parts / kit acliao Swap Meet 5 27th September 2004 02:38 AM
PCBs for Aleph 2, Aleph 3, Aleph 4 and Aleph 5 amplifiers kristijan-k Swap Meet 64 12th September 2002 07:55 AM
Matching Aleph input devices as a part of the complete amplifier? BrianGT Pass Labs 5 28th March 2002 06:11 PM


New To Site? Need Help?

All times are GMT. The time now is 09:25 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2