|
|||||||
| Home | Forums | Rules | Articles | Store | Gallery | Blogs | Register | Donations | FAQ | Calendar | Search | Today's Posts | Mark Forums Read | Search |
| Pass Labs This forum is dedicated to Pass Labs discussion. |
  |
|
|
|
Please consider donating to help us continue to serve you.
Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving |
 |
|
|
Thread Tools | Search this Thread |
14th May 2007, 06:02 PM
|
#1 |
|
diyAudio Member
Join Date: Dec 2002
Location: Denmark, Fredericia
|
Another diy-pearl...
Hi... I just finished my pearl, a week ago, so i throught it would be a good idea to 'show it off' here - I like it
 The input is mounted with a little dipswitch, so that i could switch between input-resistance load. My pickup likes 15k Ohm. Eventually look at this very interessted thread HERE The enclosures are diy, with oak-sides and 'unfinished' face plates. The one at the top is the pearl, the other below is the psu, which should contain other things as well, in the future. I just finished it as it is, so that i could listen to it  I recently bought a very worn-out thorens td316, which i cleaned up, and mounted a new belt-drive, along with a grado silver prestige pickup. I have used the pearl layout, which cviller made, and i am very satisfied with the sound of it. Thanx cviller, also for helping me a bit with this. I have no anoying 'hum or hiss' from my setup, which i connected, with the ground meeting at the output, as mentioned in the pearl-papers. Compared to another relatively expencive riaa stage, the sound is sooo much better from the pearl... But most surprising me, was the 'no hum' which the pearl gives me !!! Jesper I will post some picture's along
__________________
DIYAudio crazy.... LeachAmp, PearlPhono, Pumpkin, F4 DualMono, DDDac, HalfChang Spk., LinuxAudio, Squeezebox substitute, Drek inductorloaded pre-amp. |
|
|
14th May 2007, 06:31 PM
|
#4 |
|
diyAudio Member
Join Date: Jan 2003
Location: ancient Batsch , behind Iron Curtain
|
ugly!
__________________
my Papa is smarter than your Nelson ! tnx to  clean  thread ; Cook Book ; PSM LS Cook Book ; Baby Diyaudio FORUM ; Mighty ZM's Bloggg;I'm dumb
|
|
|
|
15th May 2007, 01:18 PM
|
#9 | |
|
diyAudio Member
Join Date: Dec 2002
Location: Denmark, Fredericia
|
Stefanoo wrote :
Quote:
I draw both channel's at the same time, and when etching was done, i seperated them. The PSU part i 'designed' myself, for fitting with my caps, and very-fast diodes (I think grinsssh...) Jesper.
__________________
DIYAudio crazy.... LeachAmp, PearlPhono, Pumpkin, F4 DualMono, DDDac, HalfChang Spk., LinuxAudio, Squeezebox substitute, Drek inductorloaded pre-amp. |
|
|
|
|
18th May 2007, 05:50 PM
|
#10 |
|
diyAudio Member
Join Date: May 2003
Location: San Diego, USA
|
Nice
Good job! How did you figure out that your cart. liked a 15K load? Just tried different values?
__________________
Retired from DIY (2010) but still lurking now and again. My DIY audio projects- PartTimeProjects.com. |
|
|
|
| Thread Tools | Search this Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| ono or pearl PCB's | mantisory | Pass Labs | 1 | 28th September 2006 11:12 PM |
| Pearl need help | dzkh63 | Pass Labs | 1 | 26th September 2006 03:16 PM |
| WTB: Pearl PCB | aire | Pass Labs | 1 | 26th February 2006 10:51 AM |
| The Pearl-X | Vince Maida | Pass Labs | 12 | 28th July 2002 07:28 AM |
| New To Site? | Need Help? |
