Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Parts Where to get, and how to make the best bits. PCB's, caps, transformers, etc.

How to Etch your own circuit board?
How to Etch your own circuit board?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 7th December 2004, 01:29 PM   #1
lgehrig4 is offline lgehrig4  United States
diyAudio Member
Join Date: Nov 2004
Location: US
Question How to Etch your own circuit board?


I purchased an etching kit from RadioShack for a small amp project. I cleaned the copper on both sides and followed the directions to a "T", but it did not work. The directions say to leave it in the solution for about 20min. In 20min almost no copper left the board. I left it in over an hour and still not all the copper dissolved, however some of the areas that were not supposed to dissolve did.

Does anyone have any advice, tricks or knowledge that they can pass on to me? The directions are lame and I'm sure there is more to it than they explain.

  Reply With Quote
Old 7th December 2004, 01:44 PM   #2
jackinnj is offline jackinnj  United States
diyAudio Member
jackinnj's Avatar
Join Date: Apr 2002
Location: Llanddewi Brefi, NJ
How to Etch your own circuit board?
it helps if the etchant is warm -- but don't warm it on a gas stove since the reaction releases hydrogen.

i now prefer to use hydrogen peroxide and muriatic acid. the hydrogn peroxide can be bought at the drugstore for under a buck for a quart, the muriatic acid is at the hardware store -- used to clean stone, it's pretty nasty stuff (Dilute hydrochloric acid). The HCl acts to accelerate the oxidizing effect of the H2O2 -- it takes less time than ferric chloride.
  Reply With Quote
Old 7th December 2004, 01:44 PM   #3
richie00boy is offline richie00boy  United Kingdom
Did it Himself
diyAudio Member
richie00boy's Avatar
Join Date: Nov 2003
Location: Gloucestershire, England, UK
How to Etch your own circuit board?
If you had to expose the board to UV light to create the mask then I'd say that you either didn't expose it for long enough or didn't clean all the residue off after developing.
  Reply With Quote
Old 7th December 2004, 02:42 PM   #4
RetroAudio is offline RetroAudio  United States
diyAudio Member
Join Date: Mar 2004
Location: Everett, WA
Send a message via Yahoo to RetroAudio
jackinnj - how many parts acid to peroxide do you use?
  Reply With Quote
Old 7th December 2004, 03:13 PM   #5
nick_g_evans is offline nick_g_evans  United States
diyAudio Member
Join Date: Sep 2004
Location: Midwest
I have just started to do this myself also. My first couple tries were hideous, but my third was a clean success!

As you have probably heard, there are several ways to mask the copper. The some ways I know of are permenent marker, laser print transfers, and the Radio Shack stickers.

I had no success getting those Radio Shack stickers to stay on, and I don't recommend them.

The only way I've tryed to etch with is using a permenent marker. It may sound like it wouldn't give good results, but with good planning, patients, and a steady hand, a nice turn-out can be had.

To ensure good results with this method be sure to clean the board before hand and after etching. In both cases I used fine-grit sandpaper, soap and water, and alcohol.

I used a Sharpie to mask. When I drew the traces, I copied and pcb layout I had found online and used the IC I needed to make sure it would line up correctly. When applying the marker, make sure that there is a thick layer of ink covering the traces, or the solution will eat right through the copper underneath.

There are a couple tricks I have heard and learned with this method. One I learned is to pull the board out mid-etch, wipe the board, and go back over the traces with the marker. This will leave thicker copper tracks and more unwanted copper disolved.

Another trick is to completely mask a whole row of a DIN IC and separate the pads with a knife after etching. This will allow for wider pads for the IC and better alignment.

Follow these steps and you should quickly learn how to cheaply and easily etch with just a marker and some solution.

I plan to try the laser printer iron-on masking next. I read a review somewhere that the best paper for this is Staples photo paper. We'll see how that turns out.

Oh yeah, by the way, make sure you don't get any solution on your hands. If you do, don't eat any crackers or anything. I did, and get not get to sleep that night because I could not get the taste and smell out of my mouth.

I hope all this helped.
Is cheap or expensive one hamburger ? - Upupa Epops
  Reply With Quote
Old 7th December 2004, 06:09 PM   #6
ingrast is offline ingrast  Uruguay
diyAudio Member
Join Date: Sep 2004
Location: Montevideo
Default PCB home fabrication

You may want to check Think & Tinker for a dry resist process I use and recommend.

Select only the chapters relevant for you, there are procedures and products for through hole, multilayer and solder mask processes also.

You may substitute an ironing appliance for laminator - be ready to spoil some trials - but cut no other corners. I can routinely make .01" tracks this way after tunning carefuly the process.

  Reply With Quote
Old 7th December 2004, 06:13 PM   #7
markp is offline markp  United States
diyAudio Member
Join Date: Oct 2003
Location: L.A., CA
I use dry transfers, toner iron-ons, and sharpies to get the patterns I want. Make sure the board is very clean and oil free(no fingerprints) and the dry transfers stick fine and work well. The best method is to get some laser printer transpearancy sheets and print your pattern on them and iron the pattern onto the board, it takes practice to get the right tempuratures on the iron but its worth it! You can go over the iron-on with a sharpie if you wish. If you have very wide traces you can go over them with nail polish. When done acetone takes the polish and toner transfer off the traces.
If it sounds good... it is good!
  Reply With Quote
Old 7th December 2004, 07:06 PM   #8
kmj is offline kmj  Sweden
diyAudio Member
kmj's Avatar
Join Date: Feb 2004
Location: Falkenberg
here's one:
Devil H@ck's page
  Reply With Quote
Old 7th December 2004, 08:07 PM   #9
TwoSpoons is offline TwoSpoons  New Zealand
diyAudio Member
TwoSpoons's Avatar
Join Date: Oct 2004
Pulsar for the toner transfer method. Read through and you'll see that toner alone is porous, leading to pinholing. Toner reactive film is supposed to fix this. They also have a sponging technique for etching, that I've not tried.

I've had good results using toner transfer, and ammonium persulfate etchant.

Keeping your etch bath at 50C is essential, also constant agitation for even etching.
  Reply With Quote
Old 10th December 2004, 10:36 AM   #10
jacco vermeulen is offline jacco vermeulen  Netherlands
diyAudio Member
jacco vermeulen's Avatar
Join Date: Oct 2004
Location: At the sea front, Rotterdam or Curaçao
Send a message via Yahoo to jacco vermeulen
Default Print the circuit directly to the PCB board

With luck you can find a HP flatbed plotter in a dumpster.
The pens should be filled with etch resistant ink.

a PCB board can be positioned on the plotter bed, the circuit is directly written on the board by the pens.
It doesn't count how one deals with winning, but how to handle a loss (© DjT)
  Reply With Quote


How to Etch your own circuit board?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
CS8402/4 Circuit Board fmak Digital Source 1 19th May 2008 03:57 PM
HELP ! Smelly Circuit Board ! poynton Everything Else 15 1st May 2007 04:00 AM
Circuit Board Blowout glen65 Everything Else 8 18th January 2007 12:09 AM
Lost 1 Zv4 ckt board..looking to buy 1 circuit board Blues Pass Labs 1 22nd March 2004 10:09 PM

New To Site? Need Help?

All times are GMT. The time now is 09:27 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio