Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Parts Where to get, and how to make the best bits. PCB's, caps, transformers, etc.

Bang & Olufsen Help!!!!
Bang & Olufsen Help!!!!
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 29th May 2004, 05:25 AM   #1
Deano is offline Deano  Canada
diyAudio Member
 
Join Date: May 2004
Location: North Bay
Smile Bang & Olufsen Help!!!!

Hi this is Deano from Canada. This is my first post. I hope I am in the right catergory. ANyway here goes: Just picked up a stereo reciever for my bedroom. It's a B&O beomaster 2400 with remote, got it at a garage sale for a song. It's in mint mint condition. I have it hooked to my B&O CDX CD player. It sounds really good but a little strained at the top end. The speakers I am using are the B&O CX 100's. I am wondering if there's anyway I can mod this reciever a little bit (better resistors, capasitors, wiring, ect...) It would not be me that would be doing the modifacations, but an electronic engineer friend of mine. I just thought I could update it a bit if it's worth it. I hope so because it's a beautiful unit. Any suggestions would be greatly appreciated ........................THANKS.
  Reply With Quote
Old 29th May 2004, 05:30 PM   #2
sreten is offline sreten  United Kingdom
R.I.P.
 
Join Date: Nov 2003
Location: Brighton UK
IMO its not wise to assume you can significantly change the
sound of an amplifier without major re-engineering.

Nevertheless if its old simply replacing all electrolytics with modern quality electrolytics will have significant effect.

sreten.
  Reply With Quote
Old 30th May 2004, 12:01 PM   #3
pinkmouse is offline pinkmouse  Europe
diyAudio Moderator
 
pinkmouse's Avatar
 
Join Date: Apr 2002
Location: Rotherham, England
Bang & Olufsen Help!!!!
Sreten is right, old electros are always worth swapping out, but if you are looking at major changes in the tonality of the system, I would look at the speakers as being more important than components in the amps.
__________________
Rick: Oh Cliff / Sometimes it must be difficult not to feel as if / You really are a cliff / when fascists keep trying to push you over it! / Are they the lemmings / Or are you, Cliff? / Or are you Cliff?
  Reply With Quote
Old 30th May 2004, 05:30 PM   #4
Deano is offline Deano  Canada
diyAudio Member
 
Join Date: May 2004
Location: North Bay
THANKS FOR YOUR ADVICE GUY'S
  Reply With Quote
Old 22nd June 2004, 07:05 PM   #5
beomuse is offline beomuse  United States
diyAudio Member
 
Join Date: Jun 2004
Location: Texas
Default BM2400 upgrades

Hi! There were two versions of the 2400 with the primary difference being on the volume control board. If you see a single IC on the volume board you have a 16-step control. Three ICs indicate the much desired 128-step system. The 2400 can suffer from many issues over the years. In refurbs I install new output Darlingtons. The ST versions of the original TI units will offer much better response overall. This might just be due to aging transistors. The rear plastic heat shield will melt if the idle pots get bad. These need to be replaced with new units so that idle can be maintained properly. Other issues such as 15 volt supply ripple and tuning voltage ripple abound after many years. Email me for questions on this model. Don't want to bludgeon the Forum!

Anthony Garza
Beomuse.com
  Reply With Quote
Old 5th March 2009, 04:53 AM   #6
SteveSun is offline SteveSun  United States
diyAudio Member
 
Join Date: Sep 2002
Location: Long Island, NY
Just like Deano: picked up a cheap B&O 2400 from e-bay with some burned bulbs.

I am thinking to replace all the bulbs with white LED and change the R3 (33 Ohms) on PCB 5 to higher value to raise the voltage across the LED to about 5V. Does anyone tried this modification? Or should I buy some 12V, 50mA bulbs to replace the original ones?

Any suggestions?
  Reply With Quote
Old 5th March 2009, 06:46 AM   #7
es44 is offline es44  Denmark
diyAudio Member
 
es44's Avatar
 
Join Date: Apr 2005
Location: Fredericia, DK
Quote:
Originally posted by SteveSun
I am thinking to replace all the bulbs with white LED and change the R3 (33 Ohms) on PCB 5 to higher value to raise the voltage across the LED to about 5V. Does anyone tried this modification? Or should I buy some 12V, 50mA bulbs to replace the original ones?

Any suggestions?
If You try to put 5 volts across a LED, it will not become very old. Find the specs of the LED's You plan to use, and don't push them.
There's some very bright ones out there, i put a couple of bright white in a Nad 705 i use as my computer amp, it works like a charm.

Best regards
Ebbe
  Reply With Quote

Reply


Bang & Olufsen Help!!!!Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
bang olufsen help N Brock Multi-Way 3 31st August 2008 06:57 PM
Bang & Olufsen connectors pinout? Bricolo Parts 7 30th May 2008 02:19 AM
Bang & Olufsen Remote 405man Everything Else 1 2nd January 2004 12:55 PM
Bang & Olufsen Loudspeakers zx3chris Multi-Way 15 9th December 2003 07:53 AM


New To Site? Need Help?

All times are GMT. The time now is 03:23 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio
Wiki