need help identifying components - Page 2 - diyAudio
Go Back   Home > Forums > Design & Build > Parts

Parts Where to get, and how to make the best bits. PCB's, caps, transformers, etc.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 13th January 2012, 08:29 AM   #11
diyAudio Member
 
Join Date: Dec 2010
Location: wigan
They look to me like axial ceramic multi layer composition. depending what they are doing in the circuit changing to metalised polyprops may do more harm than good.

Regards Ian

Last edited by madtecchy; 13th January 2012 at 08:42 AM.
  Reply With Quote
Old 13th January 2012, 08:40 AM   #12
diyAudio Member
 
Join Date: Dec 2005
Location: Kuala Lumpur
220 = 22pF and would have been a reasonable NP0 or COG dielectric.
102= 1nF and 103 =10nF would have been X7R and not much good if the value actually matters.
I am not sure what the "028" is
The ferrite part is a 200uH shielded inductor, it looks like a good quality part
  Reply With Quote
Old 13th January 2012, 10:39 AM   #13
DF96 is offline DF96  England
diyAudio Member
 
Join Date: May 2007
Quote:
Originally Posted by embrown057
The 201k may be a 200Mh choke.
200mH (or 200uH).
  Reply With Quote
Old 13th January 2012, 12:06 PM   #14
Enzo is offline Enzo  United States
diyAudio Member
 
Join Date: Sep 2004
Location: Lansing, Michigan
You read the numbers on the caps in picofarads as if you were reading a color code on a resistor. So 221 would be like red-red-brown, and would mean 220pf. 103 would mean the same as brown-black-orange, so 1-0-000pf, same as 0.01uf or 10nf.
  Reply With Quote
Old 13th January 2012, 12:17 PM   #15
diyAudio Member
 
Join Date: May 2011
Quote:
Originally Posted by madtecchy View Post
They look to me like axial ceramic multi layer composition. depending what they are doing in the circuit changing to metalised polyprops may do more harm than good.

Regards Ian
i checked the circuit, the 220 caps are paralleled with a 33kohm resistor and used between the op-amps + input to RCA ground lead. the 103 caps are also paralleled with a 33kohm resistor but this time in a feedback loop from op amp output to inverting input. a 104 is used between +12 supply to gnd of the equipment itself.
  Reply With Quote
Old 13th January 2012, 12:27 PM   #16
diyAudio Member
 
Join Date: May 2011
Quote:
Originally Posted by davidsrsb View Post
220 = 22pF and would have been a reasonable NP0 or COG dielectric.
102= 1nF and 103 =10nF would have been X7R and not much good if the value actually matters.
I am not sure what the "028" is
The ferrite part is a 200uH shielded inductor, it looks like a good quality part
i just removed the cap with 028 marking. it actually read SE 103 on the other side. the 028 must have been a manufacturer code. thanks
  Reply With Quote
Old 14th January 2012, 10:07 AM   #17
diyAudio Member
 
Join Date: Dec 2005
Location: Kuala Lumpur
The inductor is 220uH, not 220mH. A 220mH ferrite choke would be enormous.
Actually values of the order of 100uH are typical for these low power switching power supply chips
  Reply With Quote
Old 14th January 2012, 01:24 PM   #18
diyAudio Member
 
Join Date: May 2010
Location: Florida
Thank you David for the correction, your correct.
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Identifying 2 smd components sorenjepsen Parts 3 24th January 2012 11:30 PM
Identifying scrap components KatieandDad Parts 2 14th January 2012 11:38 AM
Identifying smd components pedefede Parts 2 5th January 2012 11:38 PM
Help identifying components gerb0027 Tubes / Valves 15 16th December 2010 10:40 PM
Field Guide to Identifying Components ? vonfilm Parts 6 20th October 2008 04:52 AM


New To Site? Need Help?

All times are GMT. The time now is 05:39 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2