Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Parts Where to get, and how to make the best bits. PCB's, caps, transformers, etc.

Dented ASC Caps
Dented ASC Caps
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 26th August 2009, 08:22 AM   #1
marcutan is offline marcutan  Singapore
diyAudio Member
Join Date: Jul 2006
Default Dented ASC Caps


I brought some ASC 50uf caps and 2 of them have dents at the side (prob damaged from shipping). Is it safe to use dented oil caps? Thanks.

  Reply With Quote
Old 26th August 2009, 04:07 PM   #2
alejo is offline alejo  Argentina
diyAudio Member
Join Date: Jun 2004
Location: bs.as.
Please take a photo,
  Reply With Quote
Old 26th August 2009, 04:29 PM   #3
Ty_Bower is offline Ty_Bower  United States
diyAudio Member
Ty_Bower's Avatar
Join Date: Mar 2007
Location: Newark, DE
I'd at least put a meter across it and verify the films didn't somehow get shorted against each other.
  Reply With Quote
Old 27th August 2009, 02:47 AM   #4
marcutan is offline marcutan  Singapore
diyAudio Member
Join Date: Jul 2006
They both measured around 49uf on a fluke meter. No shorts. So I guess I will go ahead and use them.

  Reply With Quote
Old 29th August 2009, 02:57 PM   #5
kavermei is offline kavermei  Belgium
diyAudio Member
kavermei's Avatar
Join Date: Jan 2005
Location: Lokeren, Belgium
Send a message via MSN to kavermei
I have some ampohm paper-in-oils that arrived dented. They work fine though!
  Reply With Quote
Old 31st August 2009, 05:23 AM   #6
casouza is offline casouza  Brazil
diyAudio Member
Join Date: Feb 2003
Location: Rio de Janeiro
There are two simple ways to measure cap leakage (lacking a capacitor tester):

Simple procedure: set your Ohmeter to its highest Meg Ohm range, connect leads to cap tabs; the cap should briefly approach zero ohms then resistance will go up as the cap charges and should read infinity when fully charged. A reading of a few Meg Ohms or anything lower means the cap is damaged.

Slightly more complicated test: connect a 1K resistor in series with the positive tab, then connect the cap to a sufficiently high DC supply, no load after or across the cap. Measure voltage across the 1 K resistor after the cap fully charges and stabilizes.
One Volt means one mA of leakage. Throw away caps that show ANY leakage, no matter how small. They mean trouble down the road.

Good luck and watch the B+, it bites!
Carlos Souza
  Reply With Quote


Dented ASC CapsHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
help! dented my fx120 audiothings Full Range 24 9th June 2008 10:06 PM
bypass caps for bypassing mylar caps? crippledchicken Multi-Way 4 27th February 2008 04:24 AM
Replacing multi-section caps with multiple caps? Sir Trefor Parts 1 29th May 2007 10:17 PM
Paralleling small value caps with large value PS caps xyrium Power Supplies 16 14th October 2005 04:06 PM
Replacing ceramic disc caps with silver mica caps? G Solid State 5 18th November 2002 01:02 PM

New To Site? Need Help?

All times are GMT. The time now is 04:02 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio