Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Parts Where to get, and how to make the best bits. PCB's, caps, transformers, etc.

Working with SMD. How to do it without specialised tools.
Working with SMD. How to do it without specialised tools.
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 11th August 2008, 10:55 AM   #1
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
Default Working with SMD. How to do it without specialised tools.

Something I have been meaning to do, put down in words and pictures how to work with surface mount components. This is a technique I developed years ago when SMD first appeared and we hadn't the luxury of re-work stations etc.
These pictures show how to remove a "postage stamp" I/C. Timewise it would take me around 6 or 7 minutes to remove.
First picture shows the tools used. Nothing special, just a good iron and braid and a jewellers screwdriver that fit well between the legs of the IC.
Attached Images
File Type: jpg imag0001.jpg (48.0 KB, 2084 views)
  Reply With Quote
Old 11th August 2008, 10:58 AM   #2
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
This shows how to apply the braid. Use a hot iron, I used a large tip as you will see, and don't be afraid to even "apply" a little fresh solder to help it wick up into the braid. You will never "unsolder" the legs this way, just quickly remove excess solder.
Attached Images
File Type: jpg imag0007.jpg (50.0 KB, 2013 views)
  Reply With Quote
Old 11th August 2008, 11:00 AM   #3
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
Using the jewellers screwdriver. Carefully ( I fitted a smaller tip in the iron for this) heat the print directly in front of the first leg and at the same time with the driver between this leg and the adjoining lever gently to "break" the bond. Do this for all the legs-- takes minutes thats all.
Attached Images
File Type: jpg imag0011.jpg (53.4 KB, 1971 views)
  Reply With Quote
Old 11th August 2008, 11:03 AM   #4
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
Here is the removed IC. It's good enough to re use. Now that is something you should never do but I will, just to show how to fit an SMD device.
Attached Images
File Type: jpg imag0017.jpg (40.3 KB, 1903 views)
  Reply With Quote
Old 11th August 2008, 11:06 AM   #5
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
This is the "unprepared" print. Using braid "wrapped" over the iron tip gently wipe the print ( never crossways - it WILL lift and be damaged) and remove all excess solder. Clean with ISO if required.
Attached Images
File Type: jpg imag0019.jpg (73.5 KB, 1898 views)
  Reply With Quote
Old 11th August 2008, 11:08 AM   #6
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
Position the new IC. Make sure it is correctly positioned. You can either try and solder each leg by applying solder to the print directly in front or try this. Put plenty on, then use the braid as earlier to remove.
Attached Images
File Type: jpg imag0022.jpg (47.8 KB, 1283 views)
  Reply With Quote
Old 11th August 2008, 11:12 AM   #7
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
Job done. Remember this was a re used IC and the pins were not perfectly straight. In reality it looks pretty good, and a new part should be virtually idestinguisable from a factory fit.
So if you are wondering how to get that OpAmp out. Now you know
I should add that a lot of parts are glued as well. No problem. Just be 100% sure ALL the legs are free and either prise off or "grip" with pliers and twist.
Attached Images
File Type: jpg imag0028.jpg (50.4 KB, 1252 views)
  Reply With Quote
Old 18th August 2008, 07:40 AM   #8
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
Nobody ever wondered how to work on SMD without the proper gear.
Actually I had nearly forgotten about this thread so thought I would bump it back so it doesn't fall off the end of the world. It was either that or go for the most number of views without a reponse
  Reply With Quote
Old 20th August 2008, 05:58 PM   #9
fernando_g is offline fernando_g  United States
diyAudio Member
 
Join Date: Nov 2007
Thanks for sharing.
Removing SMT devices is certainly a challenge.
Other techniques that have worked for me is the use of a hot air gun instead of a solder tip. The risk of damage is lower. The problem is that you can blow off a small chip cap if one is not careful!!

The components are becoming smaller and smaller, and my vision keeps getting worse and worse.
  Reply With Quote
Old 21st August 2008, 07:15 AM   #10
Mooly is offline Mooly  United Kingdom
diyAudio Moderator
 
Mooly's Avatar
 
Join Date: Sep 2007
Working with SMD. How to do it without specialised tools.
Hi Fernando,
I think a lot comes down to what you are most comfortable with, and what works for you. Never tried the hot air gun.
I remember whan we got the new PACE rework station, and all the attachments Never seen so many ruined PCB's. Guy's would heat an I/C with the special bit's fitting all round the chip ( you could smell the board frying ) then "twist and hope" usually with all the print coming off. Horrendous.
The worst thing I find is plated through via's.
All good fun
  Reply With Quote

Reply


Working with SMD. How to do it without specialised tools.Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
DIY Tools Alai Equipment & Tools 7 1st April 2009 03:30 AM
Necessary tools for diy? wixy Multi-Way 133 28th February 2007 05:34 PM
tools? tomtt Equipment & Tools 1 18th October 2006 02:35 AM
New tools edjosh23 Everything Else 25 21st July 2006 08:20 AM


New To Site? Need Help?

All times are GMT. The time now is 11:32 AM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio
Wiki