Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Parts Where to get, and how to make the best bits. PCB's, caps, transformers, etc.

panel meters
panel meters
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 5th April 2008, 05:45 PM   #1
CarlyBoy is offline CarlyBoy  Canada
diyAudio Member
Join Date: Aug 2006
Default panel meters

My searching skills are deserting me today. I though for sure I'd easily be able to find info here or on the web on the following.

I need to educate myself more about analog panel meters. These things cost way too much new. Lots of surplus stuff out there, usually doesn't have the range I want. I think the face plate can often be swapped out. Questions..

Fundamentally, what do these meters measure - current? - voltage?

Is there a basic standard full scale deflection value that most meters have? ie, Can I know if the surplus meter I'm considering purchasing will be convertible to what I want?

How can I determine the full scale deflection value of a meter?

Thanks for any help!
  Reply With Quote
Old 5th April 2008, 07:03 PM   #2
korneluk is offline korneluk  United States
diyAudio Member
korneluk's Avatar
Join Date: Jan 2005
Location: South Florida
Been there, done that. Here's the info you're looking for:






-- josé k.
  Reply With Quote
Old 5th April 2008, 07:12 PM   #3
HollowState is offline HollowState  United States
diyAudio Member
HollowState's Avatar
Join Date: Aug 2006
Location: Taxland, New Jersey
Most all meter movements measure current. Even when the full scale is stated in volts, the movement is responding to a changing current.

There are several standard full scale current ratings that are very common. But nothing is written in stone and full scale ratings can be above or below these listed. 50uA, 100uA, 200uA, 1mA, 10mA, are the most common. But I've seen 5uA & 10uA. Bird Electronics uses a lot of 30uA movements. And some movements are specified in millivolts. The units are made to be used with shunts and will have an odd full scale current value.

The full scale value of a panel meter is often (but by no means always) written down low on the meter face or card as it's sometimes called. You can usually see it by looking at a very steep downward angle.

If a meter is unmarked as to it's FS rating, then you have to test it by applying voltage to it in series with a calibrated milliamp meter. Or one can use a precision resistor in series with it and do the math by measuring the voltage drop across the resistor with a high impedance voltmeter.

As far as interchanging scales, yes you can as long as you stick to the same make and model because it's a physical thing. Mixing brands and model sizes never works out because of the physical differences in size and mounting arangments.

All this applies to the standard moving coil types with D'arsonval (jeweled pivot) or taut-band suspensions. Other less popular types like iron vane and electrostatic movements have slightly different rules. Whether a given meter will serve your needs or not is something that can best be learned by experience.

Moving coil meters must be in balance to read correctly. To test balance, position the meter pointer vertical and note where it lies in relation to the scale 0. Then re-position the pointer horizontal and look for any movement off 0. Any imbalance must be corrected by moving the weights on the pointer's cross.

There cannot, and never will be, any progress in society, vis-a-vis racism, so long as the concept of celebrating Diversity -- in it's current, politically-correct, deliberate, punitively extractive form -- continues.
  Reply With Quote
Old 7th April 2008, 12:37 AM   #4
OzMikeH is offline OzMikeH  Australia
diyAudio Member
Join Date: Mar 2007
Don;t move the weights unless the balance is grossly out.

Use a needle and a tiny dab of tacky shellac. it takes some time because you need to wait for the shellac to cure.

when setting the balance hold the meter with piointer up, down, left and right.

Vibrate it slightly to overcome the friction of the pivots. I find twirling the handle of a metal jewellers screwdriver avainst the casing is about right. You dont want so much vibration you bounce the pointer.
Help some guys with funny hair bang two rocks together really hard.
  Reply With Quote
Old 28th April 2008, 03:58 AM   #5
Evenharmonics is offline Evenharmonics  United States
diyAudio Member
Join Date: Apr 2007
That Yamamoto meter is just what I’m looking for but I can’t see myself spending $85 plus shipping per meter for my amp project.
Click the image to open in full size.

Has anyone have experience with one of these in the link below or ones that are similar?
  Reply With Quote
Old 28th April 2008, 06:07 AM   #6
Karsten Sømand is offline Karsten Sømand  Denmark
diyAudio Member
Join Date: Mar 2006
Location: Outside Copenhagen
panel meters
What about these analog 15 mA or 100 mA meters (scroll a little down the page). They are made in China but does it matter??? The price is absolutely reasonable ~ 10 $/each. Shipping should not be a major deal with these small items.


  Reply With Quote
Old 28th April 2008, 06:15 AM   #7
dsavitsk is offline dsavitsk  United States
diyAudio Member
dsavitsk's Avatar
Join Date: Jan 2005
Location: Hartford
$9.50 at Euphonia

Click the image to open in full size.
  Reply With Quote
Old 28th April 2008, 06:46 AM   #8
jormajj is offline jormajj  Finland
diyAudio Member
Join Date: Nov 2002
Location: Finland
Rod Elliot's article about panel meters:
  Reply With Quote
Old 28th April 2008, 07:32 AM   #9
Geek is offline Geek
diyAudio Member
Geek's Avatar
Join Date: Sep 2004
$9-$14 at Main Electronics in Vancouver. They mailorder

  Reply With Quote
Old 28th April 2008, 06:59 PM   #10
pmillett is offline pmillett  United States
diyAudio Member
pmillett's Avatar
Join Date: May 2005
Location: Dallas (but I am not a Texan!)
I used this cool meter face software:


It makes very nice looking meter faces.

I really like the "vintage" look meters, which are getting hard to find in the "normal" scales. But you can get good values on meters with odd scales. Most I've tried are either 50uA or 1mA movements.

Avoid sealed meters if you can - they are hard to open up to change the scale. It is possible, but difficult.

  Reply With Quote


panel metersHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Adding panel meters to Simple SE? dogfish Tubelab 6 17th June 2009 04:23 PM
Where to Buy Panel Meters? d1983 Parts 22 20th February 2009 04:31 AM
Wanted: Funky old panel meters. Spasticteapot Swap Meet 2 14th November 2006 11:14 AM
analog panel meters merlinx76 Parts 0 26th January 2005 08:46 PM

New To Site? Need Help?

All times are GMT. The time now is 12:56 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio