Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Parts Where to get, and how to make the best bits. PCB's, caps, transformers, etc.

Best Way to Fit a Neutrik NYS373 RCA Plug?
Best Way to Fit a Neutrik NYS373 RCA Plug?
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 3rd March 2008, 11:52 PM   #1
BarakaBloke is offline BarakaBloke  United Kingdom
diyAudio Member
Join Date: Oct 2007
Default Best Way to Fit a Neutrik NYS373 RCA Plug?

What's the best way to put one of these low cost Neutrik plugs on
a cable?

I'm mainly uncertain about where to solder the shield wire to and
whether you're expected to crimp the cable in the section to the
far right in the photo.

Anyone developed a good method.


Attached Images
File Type: jpg neutrik (small).jpg (39.1 KB, 449 views)
  Reply With Quote
Old 5th March 2008, 04:43 PM   #2
BarakaBloke is offline BarakaBloke  United Kingdom
diyAudio Member
Join Date: Oct 2007
OK then. Here's my illustrated guide. Let me know what you think

Referring to the picture below:

I used a soldering iron, flux cored solder wire, snipe nose pliers,
wire cutters and a jewellers loupe/magnifying glass. I also used a
flux pen which is like a felt/fibre tip pen but filled with an alcoholic
solution of solder flux. Extra flux on top of the flux inside cored
solder wire makes soldering work much better, although you
shouldn't use it to tin the end of a stripped wire as it tends to draw
the solder way up the wire into the insulation where you normally
want the wire to be flexible. If you don't have flux the following will
still work but is more difficult.

1) Apply flux just along the semicircular edge of the connector. Tin
the edge and also a little way onto the inner curved surface. When
cool apply more flux along the tinned edge.

2) Prepare the wire as illustrated, cutting and tinning the central
conductor. The length of the central conductor limits how far you
can push the cable into the connector. Cut it so they fit together as
shown in picture 3. Pull the shield wire tightly back along the cable.
Splay the shield wire out to just fit within the semicircle of the
connector you tinned in the last step.

3) Fit the cable to the connector and solder the central
conductor in place. Pull and bend back the shield wire so it sits
tightly against the tinned semicircle edge but away from the outer
surface of the semicircular tube. Apply flux to the wire where it
contacts the tinned semicircle and solder along this edge with a
little solder. Make sure the solder flows and all the shield wires are
soldered to the connector. While soldering keep the main cable
insulation slightly away from the hot area to avoid melting it.

4) After trimming the excess shield wire & solder this is the result.
Remove any further excess with a file or abrasive paper and smooth
off any sharp edges. Check for and remove any filings, dust or lose

5) & 6) At this point the connectors plastic 'chuck' can be fitted
and the connector outer shell screwed in place with the appropriate
spring cable stress reliever as required. I took the additional step
of filling the empty volume surrounding the central conductor with
epoxy resin to prevent any possibility of the wires or cable moving
in this area. I mixed micro balloons with the epoxy to increase its
viscosity but with the added bonus of reducing its dielectric constant.
You can just see the white resin mix in the photos.

Attached Images
File Type: jpg neutrik wiring.jpg (78.0 KB, 528 views)
  Reply With Quote
Old 5th March 2008, 06:57 PM   #3
MikeHunt79 is offline MikeHunt79  United Kingdom
diyAudio Member
MikeHunt79's Avatar
Join Date: Aug 2003
Location: Bristol, UK
That certainly looks like a good way, there may be a better way, but I'd be more than happy with that if they were my interconnects.
  Reply With Quote


Best Way to Fit a Neutrik NYS373 RCA Plug?Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Neutrik RT-1M jan.didden Equipment & Tools 33 2nd January 2017 10:18 PM
How to disassamble Neutrik XLR ? Bernhard Parts 6 24th June 2011 02:08 AM
FS: PCB mount Neutrik XLR's ralphs99 Swap Meet 1 15th March 2009 01:40 PM
WTB: 2.5mm plug to 3.5mm plug cable Relax Swap Meet 5 10th February 2007 12:13 AM
Neutrik XLR for Umbilical dsavitsk Tubes / Valves 14 17th August 2006 02:20 PM

New To Site? Need Help?

All times are GMT. The time now is 07:08 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio