Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

PA Systems A forum for discussion of all parts of a sound reinforcement or DJ system: loudspeakers, mixers (desks) etc.

ProSound xover wiring - wtf is going on??
ProSound xover wiring - wtf is going on??
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 26th November 2008, 09:42 PM   #1
digitallake is offline digitallake  United Kingdom
diyAudio Member
Join Date: Feb 2007
Location: England
Angry ProSound xover wiring - wtf is going on??

Hi everyone,
I had the unfortunate job of opening up a ProSound PA speaker today, in order to replace a blown bass driver (with a better one) and couldn't help noticing the crossover wiring...it is made up from a 2nd order high pass filter and LPad for the compression horn with 2 transistors (TIP122 and TIP127) on a huge heatsink and 2 power diodes. The horn is wired + to + surely it should be reverse phase for a 2nd order network. The bass driver has just got an iron cored inductor in series with it, 1st order, but really really bad design by the look of it generally.

I'm just wondering if anyone else has seen any ProSound internals before, and could shed any light on the transistor and diode business and the incorrect phase for the horn?

To cut a long story short, I instinctively bypassed the low pass filter completely, and reversed the polarity of the horn driver. It sounds tons better!!! What were they playing at???!!!

Cheers! Jim
  Reply With Quote
Old 27th November 2008, 02:18 PM   #2
Thunau is offline Thunau  United States
diyAudio Member
Thunau's Avatar
Join Date: Mar 2001
Location: PA USA
Electrical crossover order is not consequential when it comes to polarity of connection to the driver- only the resulting final acoustic slope is important.
The second order electrical circuit most likely accelerates the natural 2nd order roll off of the compression driver resulting in final acoustic slope of 24dB/oct or 4th order. That crossover type is generally connected with normal (plus to plus) polarity. It could also result in final acoustic slope of 18dB/oct, where the summation in frequency domain is the same regardless of polarity- only phase response changes.
The woofer having just a simple 1st order electrical LP filter on it could end up with a second, third or even 4th order acoustic roll off depending on the value of the inductor or in other words frequencies at which it the electrical filter is effective. So, the correct polarity of connection is always dictated by the resulting final acoustic response.
Also, the physical offset of drivers will have influence on the "proper" polarity of connection.
Without measuring you will not know for sure what polarity is better.

Putting in a "better" bass driver should always be followed by redoing of crossover. The raw frequency response and impedance will never match what was there originally, not to mention the TS parameters responsible for low frequencies behavior of your woofer in your box. Your new woofer could result in either overly boomy or weak low end depending on how it interacts with the box. Again, measuring or at least modeling would give you some answers.
"Most people just say what they know, the wise ones know just what to say."
  Reply With Quote


ProSound xover wiring - wtf is going on??Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Quality prosound woofers, drivers, horns audiokinesis Swap Meet 15 25th September 2008 05:43 AM
Series-wiring drivers instead of parallel, how does the Xover change? Glowbug Multi-Way 1 16th January 2007 04:46 AM
Wiring from xover to tweeter cpu8088 Multi-Way 1 11th January 2007 10:10 AM
I'm wiring my 4 channel 8 parallel LM4780 boards... check my wiring :) Audiophilenoob Chip Amps 9 16th August 2005 04:37 AM
Goldwood prosound? bhg41088 Multi-Way 0 7th May 2004 02:54 AM

New To Site? Need Help?

All times are GMT. The time now is 06:38 PM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio