looking for good mid woofer to use with Ribbon Tweeter.

samsagaz · 26th October 2004, 10:30 PM

hwy guys, i already buy an AurumCantus G2Si Tweeter and i want to buy 2 Mid drivers to create an MTM center box.

the characteristics of the tweeter are
Response 2khz - 40khz /-3db
Sensitivity 96db 1w/1m
Flat 6 ohm impedance
30w power handling
Fully shielded
110mm circular black face plate

can someone tellme an good Mid to use with this kick *** Tweeter?

thanks

Cal Weldon · 27th October 2004, 12:42 AM

How big?

samsagaz · 27th October 2004, 05:12 AM

4, 5, 6 "

will be 50-150 bucks each one

Will · 27th October 2004, 05:36 AM

Fostex FE206 perhaps ?

samsagaz · 27th October 2004, 05:58 AM

u tested it?

u heard it?

the Sensitivity looks nice.

i was thinking to buy the Eton 4-300 but the Sensitivity are so bad.... but the response curves are great

what do u think?

http://www.eton-gmbh.de/ShowPage.php?PId=20&LangId=0

and one more question, if my tweeter work at 96dB but its 6ohms instead 8, like the mid, the tweeter loose 3dB?

Luke (Uof Iowa) · 27th October 2004, 02:55 PM

Look at the Eton 5-880, which is used in the GR Research design that has an AC tweeter.

budwiser · 27th October 2004, 04:25 PM

I may have an older model of the 4-300 laying around. The ones with the yellow kevlar cone. Used them in a small speaker setup. Sounded good.

samsagaz · 27th October 2004, 05:18 PM

yes i was thinking to buy the 880 for the Front speakers but i think that dont will be so good, it have 87dB of Sensivity

and my tweeter 96!

i think that dont will be an good choice low my tweeter 9 dB!

4real · 27th October 2004, 06:03 PM

I used the G2si with two Monacor 135KEP woofers. The result is quite nice.

samsagaz · 27th October 2004, 06:10 PM

yes but is 89dB of sens too i want more sens dont want to lower my tweeters (i think that its not good)

26th October 2004, 10:30 PM	#1
samsagaz diyAudio Member Join Date: Aug 2004 Location: Argentina	looking for good mid woofer to use with Ribbon Tweeter. hwy guys, i already buy an AurumCantus G2Si Tweeter and i want to buy 2 Mid drivers to create an MTM center box. the characteristics of the tweeter are Response 2khz - 40khz /-3db Sensitivity 96db 1w/1m Flat 6 ohm impedance 30w power handling Fully shielded 110mm circular black face plate can someone tellme an good Mid to use with this kick *** Tweeter? thanks

27th October 2004, 12:42 AM	#2
Cal Weldon Speakerholic diyAudio Moderator Join Date: Jan 2004 Location: British Columbia	How big? __________________ Next stop: Margaritaville Some of Cal's stuff \| Cal Weldon Consulting

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Why not a ribbon tweeter instead of a horn tweeter?	Curly Woods	Full Range	9	15th July 2009 04:09 PM
Fountek ribbon tweeter 3cm2 ribbon black square alumunum faceplate	lduarte1973	Multi-Way	3	16th June 2009 08:50 AM
Dipole Ribbon tweeter isolation from dipole mid-woofer array	Bent	Planars & Exotics	5	21st May 2009 12:10 PM
good ribbon tweeter	caz	Multi-Way	5	22nd May 2004 01:08 AM
Titanium tweeter vs Ribbon tweeter	goldyrathore	Multi-Way	14	17th May 2004 07:21 PM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

27th October 2004, 05:12 AM	#3
samsagaz diyAudio Member Join Date: Aug 2004 Location: Argentina	4, 5, 6 " will be 50-150 bucks each one

27th October 2004, 05:36 AM	#4
Will diyAudio Member Join Date: Sep 2001 Location: Kuala Lumpur	Fostex FE206 perhaps ?

27th October 2004, 05:58 AM	#5
samsagaz diyAudio Member Join Date: Aug 2004 Location: Argentina	u tested it? u heard it? the Sensitivity looks nice. i was thinking to buy the Eton 4-300 but the Sensitivity are so bad.... but the response curves are great what do u think? http://www.eton-gmbh.de/ShowPage.php?PId=20&LangId=0 and one more question, if my tweeter work at 96dB but its 6ohms instead 8, like the mid, the tweeter loose 3dB?

27th October 2004, 02:55 PM	#6
Luke (Uof Iowa) diyAudio Member Join Date: Feb 2004 Location: Iowa City	Look at the Eton 5-880, which is used in the GR Research design that has an AC tweeter.

27th October 2004, 04:25 PM	#7
budwiser diyAudio Member Join Date: Jan 2004 Location: Greenwood, IN	I may have an older model of the 4-300 laying around. The ones with the yellow kevlar cone. Used them in a small speaker setup. Sounded good.

27th October 2004, 05:18 PM	#8
samsagaz diyAudio Member Join Date: Aug 2004 Location: Argentina	yes i was thinking to buy the 880 for the Front speakers but i think that dont will be so good, it have 87dB of Sensivity and my tweeter 96! i think that dont will be an good choice low my tweeter 9 dB!

27th October 2004, 06:03 PM	#9
4real diyAudio Member Join Date: May 2004 Location: Arnhem	I used the G2si with two Monacor 135KEP woofers. The result is quite nice.

27th October 2004, 06:10 PM	#10
samsagaz diyAudio Member Join Date: Aug 2004 Location: Argentina	yes but is 89dB of sens too i want more sens dont want to lower my tweeters (i think that its not good)

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)