lambda pb12 specs?? enclosure recommendations??

[sqlkev]

does anyone have the lambda pb12 sub specs by any chance??
ive searched the old archive on lambdacoustics.com and the link to the pb12 sub actually was the same link to the pb10

if youve used this sub..any thoughts??

 

[GM]

Nope, but Chris Allison has: Musiclear@aol.com

GM

 

[Duck-Twacy]

I considered the PB12 once (but took the SB12).

This is all I could find on my HD:

VAS 160 litre
Qts 0.30
Qes 0.32
Fs 21 Hz
Xmax 14 mm

 

[Bryce H.]

Here you go:

The Lambda PB12 driver is designed for vented box home use subwoofers and bass-mids. It is a high xmax, stiff poly cone with stiff poly dustcap, coated and sealed foam surround, 12 spoke aluminum basket, dual stack 120oz magnet, gold binding post, military spec coatings and glues. It is a high excursion, very low distortion, super tight bass driver. Recommended maximum crossover point is 500Hz, rated power handling is 500W. Available in 4 or 8 ohm.

*Below are specs for 8ohm model, for 4ohm model;

DCR = 3.5 ohms, 2.83VSPL = 91.6dB

Recommended cabinet of 2.0~4.0 cubic feet vented or passive radiator

Fs 21.0 Hz
Qms 4.2
Qes 0.32
Qts 0.30
Vas 160 Liters
Part# PB10 Cms 0.4 mm/N
Size 10" Mms 143 grams
Motor PL (overhung) Sd 530 cm2
Magnet 120oz (3.4Kg) Ceramic 5 Rms 4.5 Kg/S
VC diameter 51mm Bl 19.5 T/m
VC Former Black Anodized Aluminum Re 6.5 ohms
VC Wire 4 Layer Copper Flatwire Z 8 ohms
Basket Cast Aluminum 12 Spoke Le 0.3 mH
Cone Mineral Filled Hard Poly
Pe (nom) 300 Watts
Cone Profile Straight Pe (max) 500 Watts
Surround Doped Foam, 2 layer treatment
Pe (transient) 1000 Watts
Dustcap Hard Poly
"no" 0.44 %
Spider Medium stiffness Nomex 1WSpl 88.6 dB
Faraday Copper Air Gap 14 mm
Pole Vent Yes
VC Length 38 mm
Terminals Gold Plated Binding Posts Linear Xmax 14 mm (peak)
Weight 20lbs Mech Xmax 20 mm (peak)

And if its the LE version switch the Le to 2.0

Hope that helps

 

[sqlkev]

Here you go:

The Lambda PB12 driver is designed for vented box home use subwoofers and bass-mids. It is a high xmax, stiff poly cone with stiff poly dustcap, coated and sealed foam surround, 12 spoke aluminum basket, dual stack 120oz magnet, gold binding post, military spec coatings and glues. It is a high excursion, very low distortion, super tight bass driver. Recommended maximum crossover point is 500Hz, rated power handling is 500W. Available in 4 or 8 ohm.

*Below are specs for 8ohm model, for 4ohm model;

DCR = 3.5 ohms, 2.83VSPL = 91.6dB

Recommended cabinet of 2.0~4.0 cubic feet vented or passive radiator

Fs 21.0 Hz
Qms 4.2
Qes 0.32
Qts 0.30
Vas 160 Liters
Part# PB10 Cms 0.4 mm/N
Size 10" Mms 143 grams
Motor PL (overhung) Sd 530 cm2
Magnet 120oz (3.4Kg) Ceramic 5 Rms 4.5 Kg/S
VC diameter 51mm Bl 19.5 T/m
VC Former Black Anodized Aluminum Re 6.5 ohms
VC Wire 4 Layer Copper Flatwire Z 8 ohms
Basket Cast Aluminum 12 Spoke Le 0.3 mH
Cone Mineral Filled Hard Poly
Pe (nom) 300 Watts
Cone Profile Straight Pe (max) 500 Watts
Surround Doped Foam, 2 layer treatment
Pe (transient) 1000 Watts
Dustcap Hard Poly
"no" 0.44 %
Spider Medium stiffness Nomex 1WSpl 88.6 dB
Faraday Copper Air Gap 14 mm
Pole Vent Yes
VC Length 38 mm
Terminals Gold Plated Binding Posts Linear Xmax 14 mm (peak)
Weight 20lbs Mech Xmax 20 mm (peak)

And if its the LE version switch the Le to 2.0

Hope that helps

thanks a bunch

 

[PB2]

Here you go:

The Lambda PB12 driver is designed for vented box home use subwoofers and bass-mids. It is a high xmax, stiff poly cone with stiff poly dustcap, coated and sealed foam surround, 12 spoke aluminum basket, dual stack 120oz magnet, gold binding post, military spec coatings and glues. It is a high excursion, very low distortion, super tight bass driver. Recommended maximum crossover point is 500Hz, rated power handling is 500W. Available in 4 or 8 ohm.

*Below are specs for 8ohm model, for 4ohm model;

DCR = 3.5 ohms, 2.83VSPL = 91.6dB

Recommended cabinet of 2.0~4.0 cubic feet vented or passive radiator

Fs 21.0 Hz
Qms 4.2
Qes 0.32
Qts 0.30
Vas 160 Liters
Part# PB10 Cms 0.4 mm/N
Size 10" Mms 143 grams
Motor PL (overhung) Sd 530 cm2
Magnet 120oz (3.4Kg) Ceramic 5 Rms 4.5 Kg/S
VC diameter 51mm Bl 19.5 T/m
VC Former Black Anodized Aluminum Re 6.5 ohms
VC Wire 4 Layer Copper Flatwire Z 8 ohms
Basket Cast Aluminum 12 Spoke Le 0.3 mH
Cone Mineral Filled Hard Poly
Pe (nom) 300 Watts
Cone Profile Straight Pe (max) 500 Watts
Surround Doped Foam, 2 layer treatment
Pe (transient) 1000 Watts
Dustcap Hard Poly
"no" 0.44 %
Spider Medium stiffness Nomex 1WSpl 88.6 dB
Faraday Copper Air Gap 14 mm
Pole Vent Yes
VC Length 38 mm
Terminals Gold Plated Binding Posts Linear Xmax 14 mm (peak)
Weight 20lbs Mech Xmax 20 mm (peak)

And if its the LE version switch the Le to 2.0

Hope that helps

This is an old thread but I was looking for the specs on the Lambda PB12.
Seems these lines from above indicate this is the 10" PB10:
Part# PB10 Cms 0.4 mm/N
Size 10" Mms 143 grams
Actually all the other numbers look about right for a 12" driver so
perhaps the 10" figure is just a typo.

Also looking for the SAE 1204 specs ... anyone?