I am going to be making a center using the same brand driver as my mains are made from vifa tweeter & mid woofer .
I was wondering if this mid-woofer the p17sj-00-08 is compatable with this tweeter d26nc-55-06.
Could someone tell me which xo would suit these the best . thanks
I was wondering if this mid-woofer the p17sj-00-08 is compatable with this tweeter d26nc-55-06.
Could someone tell me which xo would suit these the best . thanks
Hiya,
I bet your looking at whats available in Jaycar. I reccomend the D25AG or D27TG tweeter also from Vifa, they are available from WES and other aussie distributors.
There are very many P17/D25AG crossover designs online and a few with the D27TG. This way you are sure that the drivers will match each other and has a good crossover and will only need to worry about cabinets, which is what im doing now. I have a pair of D25AG and P17 and am looking for places that'll precut mdf for me.
Here are a few of the sites i found with crossover designs for D25AG and P17
http://www.kaiaudio.com/diy2001/kaiopen.html
http://www.geocities.com/etude316/audio/TL.html
http://www.mass.com.au/pdf/designs/mp17h.pdf
http://www.audiodiycentral.com/sd200_johnk.shtml (This design also shows slight modification in crossover to allow the use of D27TG)
I bet your looking at whats available in Jaycar. I reccomend the D25AG or D27TG tweeter also from Vifa, they are available from WES and other aussie distributors.
There are very many P17/D25AG crossover designs online and a few with the D27TG. This way you are sure that the drivers will match each other and has a good crossover and will only need to worry about cabinets, which is what im doing now. I have a pair of D25AG and P17 and am looking for places that'll precut mdf for me.
Here are a few of the sites i found with crossover designs for D25AG and P17
http://www.kaiaudio.com/diy2001/kaiopen.html
http://www.geocities.com/etude316/audio/TL.html
http://www.mass.com.au/pdf/designs/mp17h.pdf
http://www.audiodiycentral.com/sd200_johnk.shtml (This design also shows slight modification in crossover to allow the use of D27TG)
my mains are the jaycar jv60 kits but I change the box design slighty . the shieled p17 has slighty different t/s paramaters
unshielded p17
Mag 415g 92mmØ zo5.8dc A² 136cm²
Fs 37Hz
Fr 37®5000Hz
Sens’ 88dB
Qms 1.55
Qes 0.45
Qts 0.35
Vas 34.7L
Code P17WJ-00-08
shielded p17
)
Coil 32mmØ
0.55mH
Zo 8 ohm (5.6ohm dc)
Mag 721g 97mmØ
A² 136cm²
Fs 41Hz
Fr 35®5000Hz
Sens’ 87dB
Qms 1.28
Qes 0.48
Qts 0.35
Vas 33.0L
Code P17SJ-00-08
how much aer these difference going to make those xo's
but I am using it for a center speaker I will need shieled or with buck magnets . the tweeter so i have been told has buck maganets .
or how far does the tweeter have to be away from the tv not to effect it
I mainly get my drivers from wes at trade . a lot cheaper than jaycar
unshielded p17
Mag 415g 92mmØ zo5.8dc A² 136cm²
Fs 37Hz
Fr 37®5000Hz
Sens’ 88dB
Qms 1.55
Qes 0.45
Qts 0.35
Vas 34.7L
Code P17WJ-00-08
shielded p17
)
Coil 32mmØ
0.55mH
Zo 8 ohm (5.6ohm dc)
Mag 721g 97mmØ
A² 136cm²
Fs 41Hz
Fr 35®5000Hz
Sens’ 87dB
Qms 1.28
Qes 0.48
Qts 0.35
Vas 33.0L
Code P17SJ-00-08
how much aer these difference going to make those xo's
but I am using it for a center speaker I will need shieled or with buck magnets . the tweeter so i have been told has buck maganets .
or how far does the tweeter have to be away from the tv not to effect it
I mainly get my drivers from wes at trade . a lot cheaper than jaycar
- Status
- This old topic is closed. If you want to reopen this topic, contact a moderator using the "Report Post" button.