diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Multi-Way (http://www.diyaudio.com/forums/multi-way/)
-   -   Home speakers with DLS. (http://www.diyaudio.com/forums/multi-way/130004-home-speakers-dls.html)

javiertoti 18th September 2008 10:35 PM

Home speakers with DLS.
 
I want to make a home boxes with my DLS UR6S caraudio speakers but i have several dudes, specially with the sizes (measures).

http://www.pwmcarsystems.nl/files/Im...ges/UR6S_F.jpg

http://img360.imageshack.us/img360/5562/specsjc3.jpg
http://img360.imageshack.us/img360/s...jpg/1/w615.png

The mark says if i want to do a home boxes i must do that...

http://img521.imageshack.us/img521/9551/cajaspx5.png
http://img521.imageshack.us/img521/c...png/1/w397.png

But I contact with them and said me that "Use a vented enclosure, volume 18 liters with vent: 3" pipe 22 cm (9") long."


Anyway i have done several graphics instead of liters and bass reflex port measures.

Pink 10L box and 5 x 7cm pipe
Orange 8,5L box and 5 x 12cm pipe
Green 18L box and 23 x 7,62cm pipe (DLS suggested)
Blue 20L box and 15 x 7,62cm pipe (DLS suggested)


http://img440.imageshack.us/img440/3...revengevd4.png
http://img440.imageshack.us/img440/c...png/1/w738.png

http://img165.imageshack.us/img165/3...gedelaycf2.png
http://img165.imageshack.us/img165/c...png/1/w734.png




What can i do?


Here are the midwoofer specs:
Outer diameter 165 mm / 6,5
Magnet diameter 85 mm / 3,35
Mounting depth 65 mm / 2,56
Mounting hole 140 mm / 5,5
Nominal power handling 150 W
Maximum power 180 W
Nominal impedance, Z 4 ohms
Sensitivity, 1 W / 1m 90 dB
Frequency response 55-4000 Hz
Fs, resonant frequency 75 Hz
Voice coil diameter 75 mm (3)
Voice coil height 13 mm /0,5
Voice coil type / former Aluminium
Voice coil wire Aluminium flat wire
Number of layers 2
DC resistance 3,50 ohm
Voice coil inductance, 1 kHz 0,21 mH
Magnet system Vented hybrid
BL product, BXL 6,68
Max. linear excursion, X max +- 3,5 mm/0,14
Suspension compliance, CMS 397
Mechanical Q factor, QMS 2,56
Electrical Q factor, QES 0,42
Total Q factor, QTS 0,36
Mechanical resistance, RMS 1,23
Moving mass, MMS 11,47 gr.
Equivalent Cas Air load, VAS 8,41 liters / 0,3 ft3
Cone / Dome material Sandwich
cone
SD - Effective piston area 122,8 cm2




1,000.000 of THANKS.

javiertoti 22nd September 2008 11:09 AM

Any advice?

javiertoti 21st January 2009 12:21 PM

Anyone?

Graham Maynard 21st January 2009 01:11 PM

Car speaskers work well in folded lines, and do not excite the same kind of one note bass response.
Triple fold with 8ft length at cone area with DIY resistive vent at end will give you a sound you would not believe possible.
Double fold with driver at top with tweeter on top of cab and adjusted forward/back to sound best can give amazing performance with small footprint (less than A4 page).

Air mass lowers Fs and resistance damps the line. You could also try 1,500uF to 2,200uF in series with driver to protect against overexcursion, also peaks LF output/current draw at about 25Hz.

This response is way below what you are simulating !

Cheers ...... Graham.


All times are GMT. The time now is 04:10 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2