Hallo from Russia!))

[sl0n]

Hi, guys!
My name is Taras and I am from Russia)
And I wish to greet everyone of this forum! Do not pay attention to my language skills, because I have started to study English recently)
But? I am "DIYer" too)) it is does't matter where Iam from? Am I right?

For a start, let me show you my last creation)) Are you ready?)))

It is jast a scooter seat with heating element for my wife.

It is heating module with "Hi" and "Lo" modes/

And fers application))))

All my most attractive photos you can see bellow the link:
http://foto.mail.ru/mail/xfanat Enjoy)
I recommend this (biggest bike show in Ural region of Russia) - http://foto.mail.ru/mail/xfanat/428
this (one of my amplifiers for scooters and moto) - http://foto.mail.ru/mail/xfanat/48
and this (my DIY Loudspeakers) -http://foto.mail.ru/mail/xfanat/21http://foto.mail.ru/mail/xfanat/21/?page=2 (just without grills)
http://foto.mail.ru/mail/xfanat/48http://foto.mail.ru/mail/xfanat/21/?page=1http://foto.mail.ru/mail/xfanat/21
Any questions are welkome!

 

[planet10]

Welcome to the forum Taras :^)

Your English is already pretty good, you'll fit in just fine.

Nice legs. Are you a photographer?

What kind of drivers in your speakers?

dave

 

[Glowbug]

Nice pics!

Yeah, you'll fit in well here, welcome

 

[freddi]

nice warming device Your speakers remind me of "Baltek" drivers - here's a crossover in my Baltek http://img229.imageshack.us/img229/523/baltekcrossover.jpg

 

[sl0n]

It Is my Wife's legs)))))
Drivers in my speaker - is USSR drivers (20 years old), caled "Radiotechnika"
Bass/mid - 35GDN-1-4 (35W RMS, 4 Ohm, 35-5000Hz)
Hi freq. - 3GDV (4-25KHz, 4 Ohm)
It is very popular drivers with fine and natural sound. I don't like carbon, alluminium or plastic drivers - only papper and silk in my mind))

Dave, I am not only photographer)) I am a technical and sales traineer in the Sony company in Russia) If you wish, I can share some additional photos about my sity (Ekaterinburg)

 

[planet10]

I'd love to see some pictures... interestingly i just did preliminary drawings for a speaker named Ekaterina.

dave

 

[iko]

Welcome to the forum Taras, and nice project there the seat heater for your wife's scooter. I made my own heated gloves as well as heated grips for the v-strom I ride, and even at -15C it was nice to have warm hands. Never had problems with cold at the bottom half

 

[sl0n]

I'd love to see some pictures... interestingly i just did preliminary drawings for a speaker named Ekaterina.

dave

Dave, I will share some photos about my sity for you and my first successful amplifiere project.
Intresting loudspeaker enclosure of your "Ekaterina". Is it TQWP?

Ikoflexer,
-15 - it is realy hard!!
I don't ride after -5 because my scooter with air-cooled engine and -5 - it is critical temperature for riding.

I have found some photos of one of my installations.
Scooter - Suzuki skyWave 400
2xJBL 5" 2-ways speakers, 2 Ohms
Amp - based on TDA1554

Red dirty scooter - it is my scooter)

 

[planet10]

Intresting loudspeaker enclosure of your "Ekaterina". Is it TQWP?

Yes, sort of. An ML-V (Mass Loaded Voigt) for the CSS EL70. A 1st pass at a 3rd speaker in my Monolith range after Mileva (Fostex FE127e) and Demetri (FE207e)

dave

 

[sl0n]

Interesting
about 8 years ago i made my first diy-acoustics. It was one-way speakers with 3GDh (wide range, 93 Db sencitivity) speakers. and 10W per channel stereo amp. There was no hi freq. and bass, bat midrange was realy amasing)
Now i trying to make psb for TDA8560, but it is impossible to me because i have not enough experience(
Can you halp me? I use standart circuit from oficial datashit.
Dimentions of PSB - 80x80mm, i want.