Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Instruments and Amps Everything that makes music, Especially including instrument amps.

Guitar amplifier wierdness
Guitar amplifier wierdness
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 3rd December 2006, 05:37 PM   #1
Frazzled is offline Frazzled  Canada
diyAudio Member
 
Frazzled's Avatar
 
Join Date: Apr 2004
Location: Regina, Saskatchewan
Exclamation Guitar amplifier wierdness

I purchased a guitar amp yesterday and opened up the chassis today to clean out the dust and crud and I found two resistors that have had one leg clipped to remove them from the circuit.

If you look at the schematic HERE look at R102 and R105 on the base of Q1 and Q2 respectively.

Any ideas why one side of the resistors would be lifted from the circuit?

Thanks,
Don
__________________
Anything worth trying is worth failing at once or twice.
  Reply With Quote
Old 3rd December 2006, 07:40 PM   #2
anatech is offline anatech  Canada
diyAudio Moderator
 
anatech's Avatar
 
Join Date: Jun 2004
Location: Georgetown, On
Guitar amplifier wierdness
Hi Don,
Believe it or not, the over current protection circuit was removed! Check the emitter resistors for the correct value and reinstall those resistors.

-Chris
  Reply With Quote
Old 3rd December 2006, 07:42 PM   #3
audiofan is offline audiofan  Canada
diyAudio Member
 
Join Date: May 2003
Location: quebec
This is a protection circuit modification to get more power before protection get in and limit current around 150% of initial rating
  Reply With Quote
Old 3rd December 2006, 07:49 PM   #4
anatech is offline anatech  Canada
diyAudio Moderator
 
anatech's Avatar
 
Join Date: Jun 2004
Location: Georgetown, On
Guitar amplifier wierdness
Hi audiofan,
Quote:
This is a protection circuit modification to get more power before protection get in and limit current around 150% of initial rating
I figured as much. It's still a stupid thing to do. The original designer had the limit designed in for a reason. I could see the protection being backed off a little, possibly a time limit out in to delay action. Disabling the circuit entirely is the wrong way to go about it.

-Chris
  Reply With Quote
Old 3rd December 2006, 09:02 PM   #5
Frazzled is offline Frazzled  Canada
diyAudio Member
 
Frazzled's Avatar
 
Join Date: Apr 2004
Location: Regina, Saskatchewan
GEEZE!

I wonder if this was done to hide a problem with the amplifier or strictly for more power...

Well as you can see they're 3.3k resistors... I'll be re-installing them shortly, I'll let you know what happens.

Thanks,
Don
__________________
Anything worth trying is worth failing at once or twice.
  Reply With Quote
Old 3rd December 2006, 11:22 PM   #6
djk is offline djk
diyAudio Member
 
djk's Avatar
 
Join Date: Feb 2001
Location: USA
"I could see the protection being backed off a little, possibly a time limit out in to delay action. "

The 100F caps should delay the VI limiter long enough so that it doesn't activate on any musical signal, but still protects in the event of a short.

At least Fender used three sets of outputs, not like the newbies here that think they can run one set and have the amp hold together.

Grounded output stage, makes for a simple drive circuit.

Some current feedback, the later Carver M1.0T used a similar scheme.
  Reply With Quote
Old 4th December 2006, 02:48 AM   #7
anatech is offline anatech  Canada
diyAudio Moderator
 
anatech's Avatar
 
Join Date: Jun 2004
Location: Georgetown, On
Guitar amplifier wierdness
Hi djk,
Yes, but Carver found the current feedback affected the gain greatly with even 1% components in the feedback loops. They therefore used a pot which caused them more grief further down the line. Just did an M 4.0t for that.

I still think disabling a protection circuit completely is not intelligent.

-Chris
  Reply With Quote
Old 4th December 2006, 02:51 AM   #8
Frazzled is offline Frazzled  Canada
diyAudio Member
 
Frazzled's Avatar
 
Join Date: Apr 2004
Location: Regina, Saskatchewan
OK but looking at the circuit it is not completely disabled only partially right?
__________________
Anything worth trying is worth failing at once or twice.
  Reply With Quote
Old 4th December 2006, 03:03 AM   #9
anatech is offline anatech  Canada
diyAudio Moderator
 
anatech's Avatar
 
Join Date: Jun 2004
Location: Georgetown, On
Guitar amplifier wierdness
Hi Frazzled,
It is for the one pair. The proper solution would be to either change all those resistors to another value, or fix the specific problem that caused the amp to go into protect (assuming the tech couldn't find the problem due to high or open emitter resistors). There is no guarantee that those transistors will current share given how that stuff usually gets fixed.

djk,
Quote:
The 100F caps should delay the VI limiter long enough so that it doesn't activate on any musical signal, but still protects in the event of a short.
Maybe not. These amps do not reproduce music. Often they are run into sustained clipping. Therefore what we instinctively have a feel for does not apply to guitar amps sometimes. I had to think about this a little.

-Chris
  Reply With Quote
Old 4th December 2006, 07:27 AM   #10
djk is offline djk
diyAudio Member
 
djk's Avatar
 
Join Date: Feb 2001
Location: USA
The delay looks like 500mS or so, and the current about 10A peak. Looks like it could pass a 400W squarewave at 4 ohms for an indefinite time, but go into limiting on lower impedances.
  Reply With Quote

Reply


Guitar amplifier wierdnessHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
i want to build a guitar amplifier elmer Instruments and Amps 24 30th March 2010 06:52 PM
2a3 Triode Guitar Amplifier 2a3geek Instruments and Amps 2 23rd November 2008 08:34 PM
807 Guitar Amplifier guitar88 Instruments and Amps 0 1st April 2008 03:34 AM
My first (guitar) amplifier layt Instruments and Amps 11 23rd October 2005 04:29 AM
DIY guitar amplifier cabinet Gabster Instruments and Amps 7 9th January 2003 03:27 AM


New To Site? Need Help?

All times are GMT. The time now is 09:24 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio
Wiki