Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Instruments and Amps Everything that makes music, Especially including instrument amps.

Notes- Line6 HD147 guitar amp power section
Notes- Line6 HD147 guitar amp power section
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Thread Tools Search this Thread
Old 18th November 2012, 05:02 AM   #1
Conrad Hoffman is offline Conrad Hoffman  United States
diyAudio Member
Join Date: Mar 2007
Location: Canandaigua, NY USA
Default Notes- Line6 HD147 guitar amp power section

There isn’t much about servicing this on-line, so here’s what I learned while fixing one recently.

This is probably the most complicated amplifier circuit I’ve ever worked on. Each paralleled output MOSFET (N-ch) is driven by its own op-amp. That means the opamps have to float up and down with the signal. They used a lot of discrete circuitry to make this happen. It’s mostly surface mount so if an output device fails, it can take all sorts of tiny components with it, right back into the level shifting circuitry. Start by checking the 5.1 ohms gate resistors, the protection zeners, the op-amps and work back as needed. Check everything! Large through-hole parts will absorb transients and abuse without a burp, but not their SMT counterparts.

Pay special attention to the 0.22 ohm 2W current balancing resistors. Normally I just look for opens, but the value is very important for this circuit to operate correctly. After everything appeared to be working, I had slightly early and non-symmetrical clipping on one channel. It turned out that one of the 0.22 ohm resistors had been stressed and rose to about 0.5 ohms. That small change is enough to cause noticeable problems, so measure more carefully than might otherwise be the case. It took me way longer to find this than it should have!

Powering the amp is a sure route to more blown parts until everything is fixed. I did find that one can tie the dual supply rails together (+ to + and – to -), then power it with a current limited bench supply of no more than 15 VDC. That lets you make measurements and confirm that no large currents are flowing.

Use a good DMM with a diode check function to probe all the transistors and diodes. If the zeners are good in the forward direction, they’re almost certainly good in reverse.

The impedance switch on the rear panel adjusts the supply voltage along with signal gain. The schematics don’t give supply voltages but for 4 ohms expect about 46 and 29, for 8 ohms 62 and 40, for 16 ohms 83 and 55. My guess is that having the switch set for 16 ohms and driving a 4 ohm load would be risky.

Finally, note that the output is fed back into the signal path at some unexpected locations, so a waveform problem almost anywhere will appear everywhere.

Though intimidating at first, logical thought and dogged perseverance will get you through this like any other amp- just start at the outputs and work your way back with the DVM. There are two identical amp sections; hopefully only one will be bad so you can compare readings with the good one.
I may be barking up the wrong tree, but at least I'm barking!

Last edited by Conrad Hoffman; 18th November 2012 at 06:16 PM.
  Reply With Quote
Old 28th November 2012, 03:19 PM   #2
JMFahey is offline JMFahey  Argentina
diyAudio Member
JMFahey's Avatar
Join Date: Mar 2009
Location: Buenos Aires - Argentina
COOL !!!
I tried to help somebody at some other Forum with a similar dead head (preamp and effects working beautifully) and finally he gave up.
Not that we were going anywhere !!
The amp became a nice"POD_in_a_cool_cabinet" driving a used cheap and LOUD Peavey rackmount power amp, so it was not wasted.
  Reply With Quote
Old 4th August 2014, 04:24 PM   #3
sap_or_id is offline sap_or_id  Indonesia
diyAudio Member
Join Date: Aug 2006
Default HD147 PSU Schematic

Hi Juan,

Can you please attached the PSU schematic of HD147

Cheers for Indonesia

  Reply With Quote


Notes- Line6 HD147 guitar amp power sectionHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
power amp for active high pass section ataul Solid State 1 9th November 2009 08:57 AM
arcam delta 290 trouble in power amp section please help homertooties Solid State 12 25th September 2008 02:26 PM
Seperate power supply for pre-amp section in integrated amp? KevinLee Solid State 8 2nd February 2008 11:20 PM
looking for schematics for a line6 duoverb amp Jamh Solid State 1 19th January 2006 03:26 PM

New To Site? Need Help?

All times are GMT. The time now is 08:07 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.79%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio