Go Back   Home > Forums > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Instruments and Amps Everything that makes music, Especially including instrument amps.

Balanced+Phantom powered Guitar Pre-amp
Balanced+Phantom powered Guitar Pre-amp
Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 22nd May 2008, 04:10 AM   #1
RonNovy is offline RonNovy  United States
diyAudio Member
 
Join Date: Apr 2008
Default Balanced+Phantom powered Guitar Pre-amp

Ok... I'm new guitar preamps and to this forum and forgive me if this has been discussed before, but here I go...

I'm looking to build a Phantom powered Balanced output guitar pre-amp for direct connection to a tube pre-amp or recorder... I've done many circuit simulations and analyzed the frequency response, phase, S/N ratio of many different circuits, but I'm still not sure if any of them will work as I can't afford to build any right now. My goal is basically to get a flat frequency response with as little noise and as little parts as possible. I've found that simple FET preamps can color the sound a bit when gain is applied to the circuit so I'm trying to use low noise op-amps. I know the sound of op-amps is said to be dull, but some EQ and a Re-amp device can fix that right?

Anyway, I'd like to know what people think of this design using an INA2137 (or two INA137s). It's simple and uses about 5.5ma which is ok for a phantom powered circuit (max 10ma). I'm not a true engineer so suggestions are welcome...

Click the image to open in full size.
  Reply With Quote
Old 22nd May 2008, 07:25 PM   #2
Minion is offline Minion  Canada
diyAudio Member
 
Join Date: May 2006
Location: Cowican Bay , vancouver island
While I"m no expert I do see a Whole bunch of problems with your design....

1) choice of Opamps ,The INA137 is NOT suitable for a Guitar preamp ,a Guitar Preamp needs a Very High Input impedance and useing a Line Reciever opamp just doesn"t have the Input impedance that you need , Pluss you haven"t even added the Input resistor that sets the input impedance....Pluss your tone controll is in the wrong spot ,The tone coltroll will only work properly when fed by a low impedance source so it should be after the opamp ,and because this type of tone controll only cuts frequencies it might be better to have a another gain stage for Makeup gain....

2) power supply, +48v will fry most opamps ,so it needs to be reduced useing a Resistor, or a Regulator or a Zenner diode....
Another problem is you can not run these opamps off of a single supply the way you have them set up...You need to have your Virtual ground connected After the Cap not before, the Bias Voltage will not enter the opamp the way you have it set up....

So all in all I would suggest that you make a proper Guitar preamp useing a High input impedance Fet Opamp with the Tone controlls after the Opamp with another Makeup gain stage....
You should also fix your Virtual earth Biasing configuration....A Fet opamp shouldn"t add any Color to the signal at low Gains but are pretty much manditory for Guitar inputs....

Also if you want a Ballanced output from the Preamp stage you should be useing a Ballanced Line Driver not a reciever (DRV134?), You can use the INA137 in the Mixer section which needs a Line reciever but even a simple opamp can be used a a Line reciever (and 2 can be used as Line drivers).....


This is all that I can see right not at a quick glance but I"m sure there are quite a few other improvements you can make, Like I said I"m no expert but I do know my way arround opamps for the most Part......

Good luck
  Reply With Quote
Old 22nd May 2008, 09:32 PM   #3
runebivrin is offline runebivrin  Sweden
diyAudio Member
 
runebivrin's Avatar
 
Join Date: Jul 2003
Location: Huddinge, Sweden
Send a message via MSN to runebivrin
Quote:
Originally posted by Minion
1) Pluss you haven"t even added the Input resistor that sets the input impedance....
I can clearly see a 1M resistor.

Quote:
Originally posted by Minion
Pluss your tone controll is in the wrong spot ,The tone coltroll will only work properly when fed by a low impedance source so it should be after the opamp ,and because this type of tone controll only cuts frequencies it might be better to have a another gain stage for Makeup gain....
I think you'll find the volume and tone controls just model what's normally built into the guitar...

Other than that, your points apply. Input impedance make INA137 useless for the application.
__________________
Do wizards use spell checkers?
  Reply With Quote

Reply


Balanced+Phantom powered Guitar Pre-ampHide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
High pitched whine when using active guitar preamp with phantom power HankMcSpank Instruments and Amps 2 25th July 2008 12:39 PM
Battery Powered Guitar Amp help filholder Chip Amps 12 29th November 2006 01:07 AM
battery powered, balanced log attenuator pcb! Brian Guralnick Pass Labs 29 27th January 2004 12:30 AM
Suggestions for a battery powered NON-balanced Mic Preamp? Phloodpants Analogue Source 4 23rd December 2002 06:22 PM


New To Site? Need Help?

All times are GMT. The time now is 11:20 PM.


Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 16.67%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2017 DragonByte Technologies Ltd.
Copyright ©1999-2017 diyAudio
Wiki