diyAudio

diyAudio (http://www.diyaudio.com/forums/)
-   Instruments and Amps (http://www.diyaudio.com/forums/instruments-amps/)
-   -   Recording into a macbook (distortion but no peaking) (http://www.diyaudio.com/forums/instruments-amps/209434-recording-into-macbook-distortion-but-no-peaking.html)

Littlebilly91 23rd March 2012 05:47 PM

Recording into a macbook (distortion but no peaking)
 
I have built a nice little circuit that runs from the speaker output to my laptop input. There is a 100W resistor dissipating the power from the amp. I use an isolation transformer after stepping down the voltage to isolate the amp and computer's ground from each other. The signal is about 2-4V at the secondary of the transformer (not noisy at all). I use some more resistance to step the signal down to 1V or so to run into my computer. I have the mic input volume on maximum and when I play through the amp, it does not peak out. However, there is a significant amount of distortion when I play loud (still not peaking).
Any suggestions? I was told by a professor that 1V, 600 Ohms was the standard for audio input.

counter culture 23rd March 2012 07:01 PM

Sounds like you haven't really got a clue as to what you're doing.

Forget the transformer.

Look up 'voltage divider' on Wikipedia. Make Z1 1k and Z2 100R. You'll need one pair for left and one for right. Turn down the amplifier volume if necessary.

Use the battery when recording, although chances are that the computer's brick supply is isolated anyway. You can check this with a DMM. See if there is continuity from any of the mains plug pins to either side of the DC jack.

If you keep the amp turned down to ~10V peak, you can use quarter watt resistors. To put it another way, turn it down if they start to smoke

cbdb 23rd March 2012 07:54 PM

Quote:

I was told by a professor that 1V, 600 Ohms was the standard for audio input.
Thats not a very good answer. There are a few "standards" for audio. For professional equipment the line level is +4 dbu (around 1 volt) for nominal level, for consumer gear its -10 dbu or about 200mv (but can vary quite a bit)and for mic inputs its anywhere from -60dbu to -20dbu. The 600ohms is for mic inputs only, and that can vary also, line inputs are usually around 50k ohms. These are nominal levels which dont include headroom, which is typically another 10 to 20 db, so the actual signal the input can handle is 20db hotter than the 200mv (for consumer gear ) or around 2 volts. (Unfortunately the loudness wars have pushed the normal level of CDs so high there is no such thing as headroom anymore.)

The macbook inputs are line level ( i cant find any exact numbers) probably consumer level. And no telling how much headroom they have.

Do what counter culture said and then use the mac meter to set the amp volume so the meter tops out a couple of segments below the max.

Littlebilly91 23rd March 2012 07:57 PM

With all due respect, I wouldn't have attempted to hook thousands of dollars worth of equipment together without putting some thought into this, or without knowing what a voltage divider was. The circuit replaces the speaker cabinet, so even if I used higher resistances rated at a quarter watt, the power from the amp has to go somewhere or the amp gets damaged. The goal is to silently record out of my half stack (which really only sounds decent at high volumes). The transformer handles audio frequencies quite well and isn't doing any harm, a small price to pay on the off chance that there is a ground loop. The amp is in mono, so I only need to worry about one channel.

The question was about noise at the input jack. If I have adressed any concerns of signal impedance, is there some other reason why the signal is distorting even though it reports no peaking.

Thank you for your response.

pinkmouse 23rd March 2012 08:00 PM

:cop:

Thread moved to appropriate area.

pinkmouse 23rd March 2012 08:03 PM

Quote:

Originally Posted by Littlebilly91 (Post 2957736)
If I have adressed any concerns of signal impedance, is there some other reason why the signal is distorting even though it reports no peaking.

Are you sure you're not just hearing the amp distortion?

Littlebilly91 23rd March 2012 08:38 PM

I know the distortion is coming from the computer. My setup is keyboard->amp->circuit->computer. My computer seems to be switching between two 'modes' (for lack of a better word). In one mode, the signal input appears quiet, peaking around -10dB. It distorts when I hit the keys hard. Without touching my circuit or amp, the computer will switch to a second mode (I don't know what causes it) where the signal looks as I would expect it to, meaning that it does peak out a little on loud notes (and only then it distorts) and the overall sound is much louder. It is almost as if the computer is preparing itself for two different kinds of inputs and it is switching between the two kinds on its own. Has anyone experienced this?

counter culture 23rd March 2012 09:11 PM

LOL.

These are the symptoms of a bad joint, almost certainly in your 'circuit', but it could be anywhere right up to the input jack on the laptop.

If you told us what value resistors you're using and which transformer there might be some hope of telling what's going on. You haven't even told us how the parts are connected.

As it is, you can leave the 100W resistor loading the output and use a resistive divider as I have suggested. Most solid-state amplifiers will work fine without the loading though.

A transformer is just looking for trouble, however. There are just so many wrong transformers you could pick and none that are intended for this purpose. If you want DC isolation, use a capacitor. You'll have to get somebody with more patience than I to explain how to dimension and select it though. Better still, use the battery or check the PSU.

dmfraser 23rd March 2012 09:22 PM

You still have far too much voltage going into the Mac. A 100W resistor connected in series with the input is useless unless it is part of a voltage divider. Instead a 15K and a 220 ohm resistor, both 1/4W will do fine with the Macbook connected across the 220 ohm resistor. Also note that the Macbook needs only about 100mV of signal to work on its line level audio input.

Or you may just want to get a speaker to line level converter box like the Radial JDX

cbdb 23rd March 2012 09:51 PM

Quote:

The circuit replaces the speaker cabinet, so even if I used higher resistances rated at a quarter watt, the power from the amp has to go somewhere or the amp gets damaged. The goal is to silently record out of my half stack (which really only sounds decent at high volumes). The transformer handles audio frequencies quite well and isn't doing any harm, a small price to pay on the off chance that there is a ground loop.
First of all, can you get at the signal pre poweramp and put a line level signal into the mac? (and not add the amps distortion and noise to your recording)

Unless your amp is a TUBE AMP no load will not damage your amp. The way your speakers only sound good at high levels has nothing to do with the way the amp sound at low levels (most SS class A/B amps will actually sound better at low levels while they are still in class A (unless noise is an issue). Get rid of the transformer, it wont improve anything (except isolation) which you probably wont need. Try it , if you get a ground hum (60hz + harmonics) run the mac of the battery.


All times are GMT. The time now is 09:12 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright 1999-2014 diyAudio


Content Relevant URLs by vBSEO 3.3.2