Tapco 4400 reverb problems - diyAudio
Go Back   Home > Forums > Live Sound > Instruments and Amps

Instruments and Amps Everything that makes music, Especially including instrument amps.

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 29th February 2012, 09:13 PM   #1
diyAudio Member
 
Join Date: Mar 2011
Default Tapco 4400 reverb problems

I have a Tapco 4400 dual reverb, solid state, unit that is not working. I replaced the fuse, and the power is there, input signal goes through and the controls for in/out level work. The meter works, the mute works, but the reverb and eq do not. I've looked extensively at the board and do not see any burned places.

Any ideas?

Thanks,

Daniel
  Reply With Quote
Old 1st March 2012, 01:07 AM   #2
Enzo is offline Enzo  United States
diyAudio Member
 
Join Date: Sep 2004
Location: Lansing, Michigan
I got one - link us to a schematic.

The vast majority of circuit failures do not result in burnt spots.

In any reverb failure, well any failure at all for that matter, isolate the problem. No reverb will either be the reverb pan, the cabling, or the support circuitry.

Disconnect the reverb pan and measure for continuity through its transducer coils - either end open?

With the thing running and reverb controls up, take the cables that went to the pan and touch the tip of each plug. One of them should make hum, and that is the return, and plugs into the OUTPUT jack on the pan. If that doesn't happen, then no reverb would happen.

With test signal applied to a channel input, scope the other cable - the drive cable - is there signal appearing there that woul;d drive the reverb pan?
  Reply With Quote
Old 2nd March 2012, 07:12 PM   #3
DrSound is offline DrSound  Israel
diyAudio Member
 
Join Date: Aug 2005
Hi dscottguitars,

Send me your e-mail and I will send you Tapco 4400 reverb service manual.
  Reply With Quote
Old 2nd March 2012, 07:39 PM   #4
diyAudio Member
 
Join Date: Mar 2011
I found out it's in the reverb pans. One of them was barely connect inside and that one works now. On the other, one of the coils has a short even though the wires and the unit look new. I was able to get it to work by moving it around and siliconed glued the wire to the brace to hold it in place and that seems fine.

Thank you all...
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Schematics for Denon POA 4400 Snorre Solid State 5 21st November 2013 10:56 AM
Looking for Tapco CP500 Schematics Zero Cool Solid State 1 27th May 2009 06:46 AM
Gibson Ga-20 rvt reverb problems blindbrett Tubes / Valves 1 11th November 2008 04:18 PM
Tapco power amplifier for sale Thims Swap Meet 0 25th March 2008 11:14 AM
denon 4400 or 6600 schematic? lt cdr data Solid State 5 28th August 2006 03:38 AM


New To Site? Need Help?

All times are GMT. The time now is 06:56 AM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright ©1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2