Go Back   Home > Forums > > >
Home Forums Rules Articles diyAudio Store Blogs Gallery Wiki Register Donations FAQ Calendar Search Today's Posts Mark Forums Read

Holton Precision Audio High quality, high performance amplifier modules and accessories

Thread Tools Search this Thread
Old 19th June 2013, 06:10 PM   #1
ze froggy is offline ze froggy
diyAudio Member
Join Date: Jul 2012
Default nxv300 R2 kit modification.

hello anthony,
just a little post to show you a modification to simplify
the trim of the idle current. i do this on my 6 modules .
my next modification is to reduce the amp gain to 26db.
in your opinion, should i reduce R24 (33k) or put a pad
on the bal input of the module?
i use four of them with a Minidsp 2X4 bal modul to built a
stereo 2 ways active, powered with 2 SMPS 2x72V 800W.
sound great, very low noise, good dynamics, very happy
with your amp .
thank's from France.
  Reply With Quote
Old 19th June 2013, 10:53 PM   #2
The Saint is offline The Saint  Australia
diyAudio Member
The Saint's Avatar
Join Date: Jul 2002
Location: Launceston, TAS, Australia
Hi Manu

To reduce the gain just change R24 to 18k ohm 0805 for 26db gain
Great to hear you like the sound quality of the nxV300 R2 modules.

Post some photos of your amplifiers?



Last edited by The Saint; 19th June 2013 at 10:57 PM.
  Reply With Quote
Old 20th June 2013, 07:16 PM   #3
ze froggy is offline ze froggy
diyAudio Member
Join Date: Jul 2012
thanks for your reply,
will replace R24 with a 18Kohm, it"s more simply.
what do you think about the idle trim modification?
the first time i try to bias the current, i turn slowly cw
the pot, reading the voltage accros a 10 Ohm in the
PS rail, read 0v, 0v.....0v( middle position),continu to turn
0v, suddenly "over" on the voltmeter(2v range) approx at 3/4
of trim position.very difficult to reach 1v with a very small
debatement of the pot.
do this with 2 modules and read the value for a correct current
(approx 50ma per transistor)=around 105 Ohm.
so decide to transform the bias circuit for more easilly and accurate
the four modules are assembly on a cooling tunnel with a
thermally controled fan, and a switch off of the PSU over 90degresC.
i"ll post photos soon.
  Reply With Quote
Old 25th June 2013, 07:27 PM   #4
ze froggy is offline ze froggy
diyAudio Member
Join Date: Jul 2012
some photos :
the modules on the heatsink!
Attached Images
File Type: jpg PICT0493.JPG (950.1 KB, 214 views)
File Type: jpg PICT0494.jpg (493.7 KB, 200 views)
File Type: jpg PICT0495.jpg (511.8 KB, 186 views)
File Type: jpg PICT0496.jpg (500.8 KB, 181 views)
File Type: jpg PICT0497.JPG (960.0 KB, 173 views)
File Type: jpg PICT0501.jpg (580.1 KB, 81 views)
File Type: jpg PICT0502.jpg (587.9 KB, 91 views)
  Reply With Quote


nxv300 R2 kit modification.Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
nxv300 build mesc Holton Precision Audio 20 9th May 2013 07:31 PM
FS: Aussie nxv300 monoblocks complete Bengali Swap Meet 4 15th July 2011 04:29 PM
help with a Chu-Moy kit design modification AzyreSky Chip Amps 2 1st May 2011 12:08 AM
Phenominal Speaker Kit - PHL 1240 and Raven R2 mbcouple Swap Meet 1 5th November 2008 01:22 PM
Audio Note M3 Kit modification la1209 Tubes / Valves 9 6th May 2008 05:48 PM

New To Site? Need Help?

All times are GMT. The time now is 05:52 AM.

Search Engine Optimisation provided by DragonByte SEO (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Resources saved on this page: MySQL 15.00%
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2018 DragonByte Technologies Ltd.
Copyright ©1999-2018 diyAudio