All Discrete Class-A Headphone Amp - diyAudio
Go Back   Home > Forums > Amplifiers > Headphone Systems

Headphone Systems Everything to do with Headphones

Please consider donating to help us continue to serve you.

Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving
Reply
 
Thread Tools Search this Thread
Old 31st May 2011, 12:37 PM   #1
diyAudio Member
 
Join Date: May 2010
Default All Discrete Class-A Headphone Amp

Hey guys,
just got a pair of AKG K701's which sound great but are a little lacking in absolute volume when driven by my sources (mostly PC soundcard), so I'm going to build an amp for them. Going for extremely low distortion and decided to go single ended class-A because I could. Won't be portable due to power consumption, but if it was made push-pull and the quiescent current was reduced a bit it might be practical.
Replace output transistors with whatever you like, I'm just using these because I have them. Paralleling them probably isn't necessary, I'm just doing it to ensure against and beta droop induced distortion (however unlikely that is at these low levels of current).
Also use whatever CCS for the output stage you like, I'll either go discrete ring type or more likely LM317 as CCS.
This will be powered by bipolar LM317 regulated 12v rails.
Spice gives promisingly low distortion figures.
Any thoughts on this design? Based around a D. Self type front end.
Attached Images
File Type: jpg Class-A headphone amp.jpg (171.6 KB, 2001 views)
  Reply With Quote
Old 31st May 2011, 02:48 PM   #2
diyAudio Member
 
Join Date: Sep 2004
Location: New Zealand
I would avoid using 2x final transistors as proper current sharing despite the emitter resistors could be problematic. Also a bootstrap is missing. The use of the caps in series for the Miller compensation is interesting. Fascinated to see if it works.

Cheers / Chris
  Reply With Quote
Old 31st May 2011, 03:46 PM   #3
diyAudio Member
 
Join Date: May 2010
Hey thanks for the reply,
Where do you think a bootstrap is necessary? On the input?
The series miller comp caps are twin pole compensation; it's what I'm using right now on my class B 130 Watt power amp and it seems to work perfectly.
When I make the PCB I'll include provision for the second output device, if sharing is an issue I'll either increase the emittor resistors or remove the second device as at these power levels its obviously not strictly necessary unless I decide to significantly increase the quiescent current.
  Reply With Quote
Old 31st May 2011, 09:42 PM   #4
diyAudio Member
 
Join Date: Sep 2004
Location: New Zealand
Hi mnturner
A bootstrap is typically applied to the output as in 5.22 (b) of the following diagram which is what I pictured when I viewed your schematic. Its purpose is to traditionally increase AC swing, however as you are only driving headphones increased output swing may not be necessary, A bootstrap might alleviate the need for the second output device and the problems that go along with current sharing
using a second device.

I would concentrate rather researching possible benefits of properties of a bootstrap lowering distortion, Cheers / Chris

Distortion In Power Amplifiers

"When a VAS-buffer is added, the drop in distortion is dramatic, as it is for the beta-enhancement method. The gain increase is ultimately limited by Early effect in the cascode and current-source transistors, and more seriously by the loading effect of the next stage, but it is of the order of 10 times and gives a useful effect. Fig 12 plots the distortion of a model amplifier with 100 Ohm input pair degeneration resistors, showing the extra distortion from a simple VAS. However, the beta-enhanced version has the THD submerged in the noise floor for most of the audio band, being well below 0.001%. I think this justifies my contention that input-stage and VAS distortions need not be problems; we have all but eliminated Distortions 1 and 2 from the list of eight."
  Reply With Quote
Old 1st June 2011, 04:00 AM   #5
diyAudio Member
 
Join Date: May 2010
Was it the bootstrapped VAS you were referring to? I've used an active current source for the vas instead, and the vas is buffered by the use of the darlington type output stage (q27)
  Reply With Quote
Old 1st June 2011, 05:20 AM   #6
diyAudio Member
 
Join Date: Sep 2004
Location: New Zealand
I look forward to seeing how it goes with the AKG's
Cheers / Chris
  Reply With Quote
Old 1st June 2011, 05:28 AM   #7
diyAudio Member
 
Join Date: Mar 2007
Location: Canandaigua, NY USA
I built a low power amp almost identical to this, but with a conventional darlington output. I went with a lower feedback network impedance and a few other values differed slightly, but the performance was first rate and distortion numbers generally under .001% across the audio band. The key to achieving those numbers in the real physical design has a lot to do with how/where you ground various parts of the circuit. My transistor compliment was MPSA56 and MPSA05 for the small stuff, and output darlingtons consisting of 2N2218+TIP32A and 2N4037+TIP31A. It ran on +/- 18VDC. (I'd dump the 3055s in a heartbeat!)
__________________
I may be barking up the wrong tree, but at least I'm barking!
  Reply With Quote
Old 1st June 2011, 03:03 PM   #8
diyAudio Member
 
Join Date: Mar 2007
Location: Canandaigua, NY USA
Sorry, I didn't look at my schematic closely- the output pairs aren't darlingtons but npn-pnp pairs. I'm too lazy to look up the proper name at the moment.
__________________
I may be barking up the wrong tree, but at least I'm barking!
  Reply With Quote
Old 1st June 2011, 04:05 PM   #9
diyAudio Member
 
Join Date: May 2010
Sounds like complementary feedback pair or Sizklai pairs (or however you spell that guy's name). That's my preferred output stage topology, I've used it in a couple of class B power amps.
Did your headphone amp use complementary devices with a bias setting?
I thought about that but in this design I've just used the single ended output because it avoids having to use a Vbias transistor etc. to simplify PCB layout at the expense of efficiency.
I have a feeling using only one polarity of output device with a constant current load to set the quiescent current might possible be more linear too, but I'm not sure about that and spice sims haven't shown much difference either way.
  Reply With Quote
Old 3rd June 2011, 06:24 PM   #10
diyAudio Member
 
Join Date: May 2010
I got impatient and couldn't be bothered making a PCB for the amp straight away, so in the meantime I knocked this together on perfboard. Regulated +/- 13v supply with ~50VA +/-12Vac trafo scavenged from and old integrated amp, 2200uF per rail before regulators and 470uF low ESR caps after regulators and WIMA polycarb input caps. The gain of about 4 which seems to be about right for my sources and these headphones.
I reduced the quiescent current to 125mA because I've use a pretty small heatsink (which is still only barely adequate), but even at this level the amp can still put about 480mW into my phones (more than enough to blow them up).
And all made from stuff out of the junk box
Anyway, it sounds much better than trying to run the phones straight from source and lets me get the phones up to ear-shattering levels if I'm not careful with level controls
Attached Images
File Type: jpg head_amp_opamp.jpg (104.8 KB, 1350 views)
  Reply With Quote

Reply


Hide this!Advertise here!
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Discrete Single End TRUE Class A HeadPhone Amplifier lineup Headphone Systems 30 29th May 2009 10:44 PM
THAT transistor headphone amp (250ma discrete opamp) design sanity check. Russ White Headphone Systems 19 13th December 2007 01:52 PM
Discrete simple headphone amp kubeek Headphone Systems 15 7th September 2007 05:13 PM
Discrete Headphone Amp Q weinstro Headphone Systems 1 24th September 2003 10:48 PM


New To Site? Need Help?

All times are GMT. The time now is 09:54 PM.


vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2014 DragonByte Technologies Ltd.
Copyright Đ1999-2014 diyAudio

Content Relevant URLs by vBSEO 3.3.2