|1st September 2013, 01:16 AM||#1|
not politcally affiliated
Join Date: Feb 2006
Blog Entries: 7
GB for Salas Folded Simplistic Phono PCB
I am proud to offer the Salas Folded Simplistic Phono Preamp PCB.
In Salas words :
"It uses a folded cascode input stage, passive RIAA filter, common source second stage, a source follower buffer with constant current bias. No form of feedback between stages is employed.
It can be made for different voltage gain. Input load is switchable. Suitable for LMC-MC-HMC-MM. (see build guide)
There is an official double layer PCB available for it that carries two channels and two MOSFET
It comes in one piece and it is pre-grooved to be breakable into separate channels."
The PCB is available for $52USD (~39 Euro).
The shipping costs is 8.00 USD (~6 Euro).
Accepting USD PayPal only.
This project took significant development costs and a long time cycle. It will probably be a limited edition for one or two runs depending on demand. Good components and nice boxes for it will be money well spent judging from my prototype's sonic results.
Minikits will be made available as well and will contain limited parts - resistors and transistors for the Shunt supply portion and the RIAA caps VISHAY MKP 1837.
Please subscribe to this thread as well as check out the sign up spread sheet for "Salas Board" in my signature.
The GB will close on TO BE DETERMINED as of 12/23/13
Payment is via invoice only. Please send me a private message with PayPal email and I will forward you an invoice based on spreadsheet's data.
Here is the minikit details.
It is designed to allow for a bulk packaging of parts to get transistors and resistors for the power supply, and some small parts for the phono section.
Price is $53.00
3MM /Green/Red LED 20ma D1-4 10/20
BC560C Fairchild High HFE (600 typical) Q3y 6
2SK117GR Q2,Q3,Q5 10
BC550C Fairchild HIGH HFE (600 typical) Q4x 6
Vishay CFP 15R 100PPM metal film 2-3W R1x 2
VISHAY - MRS25 Series .6W 6.2K 50ppm R3x (high IDSS) 2
MRS-25 9.1k R3x 2
MRS25 120R R2x,R4x 4
MRS25 33.2R R6x 2
MRS25 27.4R R6x (high IDSS) 2
Welwyn MFR4 1R2 1% 50ppm
Vishay CFP 1.2K 100ppm 2W R13 2
Bourns 3296Y 1K VR1 2
Bourns 3296Y 2K VR2 2
IRF9610PBF Q1x 2
IRF9530PBF Q6x 2
4 position SPST 2
KEMET 0.1uf 100v 5% C3x 2
Vishay MKP-1837 .047 1% C1 2
Vishay MKP-1837 .015 1% C2 2
Wima 150pf 2.5%, plus 100pf sytrene cap C2Y2+2 (to trim to liking)
2SK369BL matched pair - $10.00usd
2SK369BL matched quads - 25.00usd
2SK170BL's Q4 (8.2-8.5ma),Q5 (7.5-8.1ma),Q6 (8.6ma or higher ma idss) triple pairs - 22usd
PRP RIAA Resistor's 8usd for 4 resistors, enough for stereo set of boards
PRP 9372 1/4W 25ppm .1% 47K -2
PRP 9372 1/4W 25ppm .1%6.754k -2
Here is the new RAW PSU that people have requested. Use this before the Folded Boards Shunt Supply as described in Folded Guide.
These are 15.00 each.
Salas Boards GB 2015 #2 shipping| Dual Rail 40mm cap power supplies available PM | Hot-Rod DCB1 boards and kits available PM | SONY VFET 2 AL Board Sign up sheet Click Here to Sign Up!
Last edited by Tea-Bag; 25th August 2014 at 12:53 PM. Reason: added minikit
|1st September 2013, 09:25 AM||#3|
I' m in for a board too.
"Without deviations from the norm, progress is not possible" - Frank Zappa
|1st September 2013, 10:09 AM||#6|
Join Date: May 2010
I m in for two boards and minikits. thanks a lot for doing this guys
Second harmonic and semi-sweet wine for everyone...
|Thread Tools||Search this Thread|
|Thread||Thread Starter||Forum||Replies||Last Post|
|The simplistic Salas low voltage shunt regulator||iko||Power Supplies||7201||3rd October 2015 05:35 PM|
|OLD THREAD Simplistic Mosfet HV Shunt (The Simpler Simplistic Design by Salas)||quanghao||Quanghao Audio Design||460||6th May 2012 11:13 PM|
|New To Site?||Need Help?|