Discrete Low Jitter Clock GB

[acccruz]

Hi:

I have 2 units for sell - 11.2009Mhz, and an extra 16.934 cristal

Make me an offer.

Thank you!

 

[amc184]

You must remove the flat washers from underneath the heads of the regulator mounting screws. With it assembled like that you'll probably short the regulator's output to ground.

 

[acccruz]

It´s done! Thank you very much!

 

[Tan Lik Hua]

Hi Anton,

I interested your LJC clock kitset and LJP AC power supply kitset for CD player Microseiki CD-M2 and Marantz CD-16
Thanks

 

[audiorado]

Hi Anton,
....plese tell if there will be some kit for sale soon.I would need one piece of your clock module.
Regards,Rado

 

[PerecNS]

Hi still possible to buy DC version / 11.2896MHz for CD (Marantz TDA1541/1543 based DAC)

 

[acccruz]

Hi:
I have two boards completly populated and never used. If desired, contact me please,
Antonio

 

[Elias Zacharopoulos]

is the frequency 16.9344 ? What is the cost for 1pc ? Can you ship it to Greece (by mail) ?

 

[Elias Zacharopoulos]

what is the cost ?

Hi:
I have two boards completly populated and never used. If desired, contact me please,
Antonio

for one (1) unit ? Will you ship it to Greece by regular post ?

 

[acccruz]

Hi:

Now I only have one unit with crystal 11.2009Mhz - the other one it´s sold.

Shipping to Greece by registered mail it´s possible.

Thank you,
Antonio

 

[Elias Zacharopoulos]

Marantz CD-63SE

Hi:

Now I only have one unit with crystal 11.2009Mhz - the other one it´s sold.

Shipping to Greece by registered mail it´s possible.

Thank you,
Antonio

Thank you Antonio but I need 16.9344MHz (Marantz CD-63SE)

 

[Wungun]

Bringing this thread back....lol

So I'm building a DAC, which uses a 100Mhz crystal on board (with decent PSU).
I already have your low jitter clock which Ive used on my Xonar soundcard...
Is it possible to upgrade your device with 100Mhz output?

 

[Wungun]

Bump ttt

 

[Wungun]

delete

 

[amc184]

25MHz should be fine, you only need to change the crystal. 100MHz however is just too far from the frequency I optimized it for. It might oscillate, but not well.

 

[Wungun]

Thanks for the reply...
Using the LJC in place of my mother board crystal...

 

[ckwong99]

Anyone know this clock support 10M for my Teac UD503 ? And does any any one have these boards (AC supply and bare main board)?

 

[maguba1410]

Hello Anton,
is any kit still available ?
I would like to buy the 7-20V one.
Waiting to receive your reply, many thanks in advance
Cheers, Massimo

 

[Richard]

Hi Anton,

I'm also interested in a couple of your clock PCBs. Tried sending you a PM, but your inbox is full.

I'm also interested in the 7-20V one.

Cheers,
Richard

 

[maguba1410]

Dear Anton,
I would like to build your LJC circuit and wondering if you could sell any PCB yet.
Last but not least, please, let me ask you :
- Would it be benficial to add a Pulse Transformer (like 10/100base tx/rx) on the output to "un-couple" the LJC source to the CD Player receiver ?
Waiting to receive your answer, many thanks in advance
Kind Regards
Massimo