GB Thread for Salas SSLV1.1 BiB shunt reg - Page 40

necplusultra · 22nd July 2011, 11:53 AM

with a colorful adjective before the manual!
... or is it used as a verb? perhaps an adverb but definitely not a noun in this case.

LucasAdamson · 22nd July 2011, 12:04 PM

But Andrew, surely it translates as, "Read the FULL manual" Right?

palmito · 22nd July 2011, 01:23 PM

Or "read the fine manual"...

necplusultra · 22nd July 2011, 01:57 PM

if you change the manual's color font to #FF00FF

you would have to "read the Fuschia manual"

acidbrain · 22nd July 2011, 02:07 PM

LOL, luckily this is not the build thread.

Salas · 22nd July 2011, 02:16 PM

The ''FINE'' manual also says not to sweat much over IDSS because it will work anyway. You can get not so bright LEDS and lower Rset to reach target CCS if a low IDSS JFET happens feeding them, a not following Vo examples Vref, or a hotter BC550/560 in high Vo situations. Its good to have it balanced but if you had soldered them in, give it a go first. The GR JFETs don't spread more than 3mA apart if you get a bit lucky.

Franz Gysi · 23rd July 2011, 04:42 PM

I received my boards and kits today.

Thanks for all effort and also for postponing my order, as I was in vacation. Special service!

About the results, I will post in the build thread soon.

Franz

william2001 · 23rd July 2011, 05:15 PM

I've got my regs together now. Anxious to fire this thing up. Looks ready for business with the OnSemi MSRF's, Panasonic 10,000uF caps, 10uF KEMET MMK's everywhere, Vishay 5W wirewounds, black Molex terminal blocks....etc. Just need to get my DAC chassis plate re-drilled. I'll sink the fet's to the floor, as the chassis plate is very thick aluminum.

Tea-Bag · 23rd July 2011, 05:16 PM

Quote:

Originally Posted by william2001

I've got my regs together now. Anxious to fire this thing up. Looks ready for business with the OnSemi MSRF's, Panasonic 10,000uF caps, 10uF KEMET MMK's everywhere, Vishay 5W wirewounds, black Molex terminal blocks....etc. Just need to get my DAC chassis plate re-drilled. I'll sink the fet's to the floor, as the chassis plate is very thick aluminum.

Lots of people are building PS for their Buffalo DACs.

claudio · 24th July 2011, 10:10 AM

Boards received, thanks.

Claudio

22nd July 2011, 12:04 PM	#392
LucasAdamson diyAudio Member Join Date: Feb 2009	But Andrew, surely it translates as, "Read the FULL manual" Right? __________________ Lucas

24th July 2011, 10:10 AM	#400
claudio diyAudio Member Join Date: Feb 2002 Location: Italy	Boards received, thanks. Claudio __________________ ______________________________ My Home Page: www.claudionegro.com

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
GB: Salas Shunt for Squeezebox	mravlca	Group Buys	8	18th July 2011 04:34 PM
My PCB design of Salas SHunt Reg	Lazybutt	Power Supplies	24	14th July 2011 04:11 PM
Wtd: Salas shunt reg boards	RichLund	Swap Meet	1	23rd April 2010 10:28 PM
Modified Salas Mosfet Shunt Reg	mach1	Tubes / Valves	2	18th December 2008 05:36 AM

New To Site?	Need Help?
Register to Participate Search Privacy Statement Contact Us	Frequently Asked Questions Did you forget your password? Mark Forums Read


	Please consider donating to help us continue to serve you. Ads on/off / Custom Title / More PMs / More album space / Advanced printing & mass image saving

22nd July 2011, 11:53 AM	#391
necplusultra diyAudio Member Join Date: Jan 2011 Location: sitting down	with a colorful adjective before the manual! ... or is it used as a verb? perhaps an adverb but definitely not a noun in this case.

22nd July 2011, 01:23 PM	#393
palmito diyAudio Member Join Date: Dec 2010 Location: Florida,US	Or "read the fine manual"...

22nd July 2011, 01:57 PM	#394
necplusultra diyAudio Member Join Date: Jan 2011 Location: sitting down	if you change the manual's color font to #FF00FF you would have to "read the Fuschia manual"

22nd July 2011, 02:07 PM	#395
acidbrain diyAudio Member Join Date: May 2008	LOL, luckily this is not the build thread.

22nd July 2011, 02:16 PM	#396
Salas diyAudio Chief Moderator Join Date: Oct 2002 Location: Athens-Greece	The ''FINE'' manual also says not to sweat much over IDSS because it will work anyway. You can get not so bright LEDS and lower Rset to reach target CCS if a low IDSS JFET happens feeding them, a not following Vo examples Vref, or a hotter BC550/560 in high Vo situations. Its good to have it balanced but if you had soldered them in, give it a go first. The GR JFETs don't spread more than 3mA apart if you get a bit lucky.

23rd July 2011, 04:42 PM	#397
Franz Gysi diyAudio Member Join Date: Oct 2007	I received my boards and kits today. Thanks for all effort and also for postponing my order, as I was in vacation. Special service! About the results, I will post in the build thread soon. Franz

23rd July 2011, 05:15 PM	#398
william2001 diyAudio Member Join Date: Sep 2001 Location: Midwest	I've got my regs together now. Anxious to fire this thing up. Looks ready for business with the OnSemi MSRF's, Panasonic 10,000uF caps, 10uF KEMET MMK's everywhere, Vishay 5W wirewounds, black Molex terminal blocks....etc. Just need to get my DAC chassis plate re-drilled. I'll sink the fet's to the floor, as the chassis plate is very thick aluminum.